Results 221 to 230 of about 90,832 (301)

Marginal gap of printed, milled, and heat‐pressed two‐piece polyetheretherketone abutments before and after thermal cycling, and their pull‐off bond strength after thermal cycling

Journal of Prosthodontics, EarlyView.
Abstract Purpose To evaluate the marginal gap of two‐piece polyetheretherketone (PEEK) abutments fabricated with different methods, before and after thermal cycling, while also focusing on their pull‐off bond strength. Materials and Methods A two‐piece abutment was virtually designed after digitizing a titanium‐base (Ti‐base) abutment.
Almira Ada Diken Türksayar, Burcu Kanpalta, Naime Bilinç Bulucu, Sandra Schulnig, Sebastian Spintzyk, Münir Demirel, Mustafa Borga Donmez   +6 more
wiley   +1 more source

Recent advances in experimental and clinical applications of chest electrical impedance tomography: a narrative review. [PDF]

Intensive Care Med Exp
Frerichs I, Scaramuzzo G, Jonkman A.
europepmc   +1 more source

Biomechanics of the implant‐supported full arch fixed complete denture manufactured by milling and injection techniques: An experimental and FEA study

Journal of Prosthodontics, EarlyView.
Abstract Purpose This study aims to characterize the mechanical properties of implant‐supported full arch fixed complete dentures manufactured by milling and injection techniques. Materials and Methods Twenty‐two samples with milling and injection manufacturing techniques were fabricated.
Mustafa Gürkan, Ovul Kumbuloglu, Makbule Heval Şahan, Mert Narin, Halis Kandaş, Yusuf Arman, Hasan Yildiz, Mahmut Pekedis   +7 more
wiley   +1 more source

Ventilator-induced lung injury: from mechanisms to integrated clinical management. [PDF]

Front Med (Lausanne)
Li LC, Yang DH, Yang M, Zhang H, Li L, Lu XY, Wang L, Luo H.   +7 more
europepmc   +1 more source

Case studies to enhance graduate employability:Emerging careers [PDF]

, 2015
Crane, Linda H, Dowling, David, Judd, Madelaine-Marie, Kinash, Shelley, Knight, Cecily, Lovell, Caroline, McLean, Matthew, Mitchell, Kirsty, Schwerdt, Rosalind   +8 more
core  

Effect of surface treatments on the bond strength between additively manufactured or injection‐molded high‐performance polymers and titanium

Journal of Prosthodontics, EarlyView.
Abstract Purpose To investigate the effect of surface treatment and fabrication techniques of high‐performance polymers on their shear bond strength (SBS) to grade IV titanium. Materials and Methods A total of 120 pre‐milled titanium abutments were sectioned.
Ahmet Serkan Küçükekenci, Doğu Ömür Dede, Oğuz Süleyman Özdemir, Burak Yilmaz   +3 more
wiley   +1 more source

EXPRESSION OF CONCERN: PCV-VG Combined Individualized PEEP Determination in One-Lung Ventilated Patients With PEEP Step Change Direction: A Randomized Controlled Trial. [PDF]

Clin Respir J
europepmc   +1 more source

Anesthetic management of a patient with acquired bronchobiliary fistula: a case report. [PDF]

BMC Anesthesiol
Zhao W, Cheng B.
europepmc   +1 more source

Technique for retrieving a locked implant‐supported bar overdenture following direct attachment pick‐up procedure

Journal of Prosthodontics, EarlyView.
Abstract Implant‐assisted complete dentures, particularly those utilizing implant‐supported bar systems (RP‐4), offer significant advantages in patient satisfaction and prosthetic function compared to conventional dentures. However, complications can arise during the direct intraoral pick‐up procedure, such as inadvertent resin polymerization in ...
Weiqing Liu, Toshiki Nagai, Daizo Ishiguro, Wei‐Shao Lin   +3 more
wiley   +1 more source

A physiologic Comparison of Continuous Neurally Adjusted Ventilation (NeuroPAP) Versus Neurally-Adjusted Ventilatory Assist (NAVA) in Infants With Respiratory Failure. [PDF]

Pediatr Pulmonol
Plante V, Tabone L, Beck J, Sinderby C, Morneau S, Lodygensky GA, Sauthier M, Baudin F, Emeriaud G.   +8 more
europepmc   +1 more source