Results 41 to 50 of about 14,616 (273)
Understanding Operando Water Management in Hydroxide‐Exchange‐Membrane Fuel Cells
Advanced Materials Interfaces, EarlyView.Effective water management is vital for high‐performance hydroxide‐exchange‐membrane fuel cells. Using a custom water‐flux station, this study quantifies how membrane thickness, microporous layers, and operating conditions dictate internal water transport.
Catherine M. Weiss +4 more
wiley +1 more source
Compact personal distributed wearable exposimeter [PDF]
, 2015 A compact wearable personal distributed exposimeter (PDE) is proposed, sensing the power density of incident radio frequency (RF) fields on the body of a human.
Joseph, Wout +5 more
core +1 more source
Degradation Mechanisms in PEM Water Electrolysis: Diagnosis and Impact
Advanced Materials Technologies, EarlyView.This review provides an analysis of degradation mechanisms in proton electrolyte membrane water electrolyzers (PEMWE), focusing on all key components. It discusses diagnostic and measurement techniques for evaluating degradation, less‐studied mechanisms, and an expert survey.
Annik Bernhardt +11 more
wiley +1 more source
Readability of Patient Educational Materials in English Versus Arabic
Health Literacy Research and Practice, 2019 Little research has been done about patient educational materials (PEMs) written in Arabic. Readability of Arabic PEMs has not previously been assessed because, until recently, there was no validated Arabic readability assessment tool.
Abdulaziz Malik +2 more
doaj +1 more source
Additive Manufacturing of Ni‐Based Thermoelectric Materials for Waste Heat Recovery
Advanced Materials Technologies, EarlyView.Thermoelectric generators convert waste heat into electricity but are constrained by conventional fabrication. Here, laser powder bed fusion enables direct printing of customised n‐type Cu60Ni40 and p‐type Ni90Cr10 legs. The assembled module achieves 0.8% efficiency at ΔT = 419 K, demonstrating scalable additive manufacturing of eco‐friendly, design ...
Karolin Amstein +6 more
wiley +1 more source
Energies, 2021 The aim of this study is to verify the reliability of NOx emissions measured using Smart Emissions Measurement System (SEMS) equipment in comparison with the NOx emissions measured using certified Portable Emissions Measurement System (PEMS) equipment ...
Young Soo Yu +3 more
doaj +1 more source
Scalable Deep Traffic Flow Neural Networks for Urban Traffic Congestion Prediction
, 2017 Tracking congestion throughout the network road is a critical component of Intelligent transportation network management systems. Understanding how the traffic flows and short-term prediction of congestion occurrence due to rush-hour or incidents can be ...
Elmasri, Ramez +3 more
core +1 more source
PEMS EMISSIONS TESTING OF HEAVY DUTY VEHICLES/ENGINES: ASSESSMENT OF PEMS PROCEDURES IN FULFILMENT OF ARTICLE 14(3) TO REGULATION (EU) 582/2011 [PDF]
, 2015 The Euro VI Regulation (EC) No 595/2009 and the implementing Regulation [2] (EC) 582/2011 introduces a procedure for PEMS testing as a mandatory part of the type approval legislation in order to check the conformity of heavy-duty engines with the ...
MENDOZA VILLAFUERTE PABLO +1 more
core +1 more source
Helix Alignment, Chevrons, and Edge Dislocations in Twist‐Bend Ferroelectric Nematics
Advanced Science, EarlyView.The recently discovered twist‐bend ferroelectric nematic (NTBF) is the new member of the multiferroic family, representing a fluid with an oblique helicoidal (heliconical) periodic structure of spontaneous electric polarization. The work presents a thorough exploration of the material properties of this phase, how the periodic modulation of ...
Bijaya Basnet +8 more
wiley +1 more source
Nanomaterials, 2020 Surface functionalization of materials to improve their hemocompatibility is a challenging problem in the field of blood-contacting devices and implants. Polyelectrolyte multilayer films (PEMs), which can mimic functions and structure of an extracellular
Gabriela Imbir +6 more
doaj +1 more source