Results 191 to 200 of about 1,445,125 (331)

Manufacturing Continuous Fiber‐Reinforced Printing Filaments: Development of a Post‐Consolidation Unit

Advanced Engineering Materials, EarlyView.
A novel, temperature‐controlled post‐consolidation unit is developed to test its potential to improve the melt impregnation process used to manufacture continuous fiber‐reinforced filaments for additive manufacturing of high‐performance thermoplastics.
Daniel Beermann, Patrick Schiebel, David May   +2 more
wiley   +1 more source

Effects of strong parametric excitation on cantilever beam: non-perturbative approach. [PDF]

Sci Rep
Moatimid GM, Amer TS, Elagamy K.
europepmc   +1 more source

A quasi-periodic two-component dynamical model for cardio-signal synthesis using time-series and the fourth-order Runge-Kutta method [PDF]

, 2012
Dmitry Vladimirovich Kazakov
openalex   +1 more source

A Thermodynamic 3D Model for the Simulation of Diffusion‐Controlled Alloying Processes in Heterogeneous Material Structures

Advanced Engineering Materials, EarlyView.
A numerical model resulting from irreversible thermodynamics for describing transport processes is introduced, focusing on thermodynamic activity gradients as the actual driving force for diffusion. Implemented in CUDA C++ and using CalPhaD methods for determining the necessary activity data, the model accurately simulates interdiffusion in aluminum ...
Ulrich Holländer, Leonhard Holländer, André Langohr, Hans Jürgen Maier   +3 more
wiley   +1 more source

Optical wave propagation in magneto-optic waveguides with generalized anti-cubic model. [PDF]

Sci Prog
Baber MZ, Yasin MW, Ahmed N, Arif K, Ceesay B.   +4 more
europepmc   +1 more source

Existence of positive periodic solutions of higher-order functional difference equations [PDF]

, 2014
Xinge Liu, Mei-Lan Tang
openalex  

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Noise-resilient exceptional point sensing with immunity to undesired perturbations. [PDF]

Sci Adv
Landers S, Tuxbury W, Vitebskiy I, Kottos T.   +3 more
europepmc   +1 more source

Periodic Solutions and the Stability in a Non-linear Parametric Excitation System : 2nd Report, Consideration of Solutions in the Neighborhood of Resonance of Order 1

, 1986
Sumio Yano, Tadashi KOTERA, Tsutomu Hiramatsu   +2 more
openalex   +2 more sources

Piezoresistive Monitoring of Carbon Nanomaterial‐Reinforced Epoxy Composites Under Cyclic and Fatigue Loading: A Review

Advanced Engineering Materials, EarlyView.
Carbon nanomaterial‐reinforced epoxy composites exhibit pronounced piezoresistive behavior, enabling intrinsic damage sensing under cyclic and fatigue loading. This review critically compares carbon nanotube and graphene systems, correlating filler content, percolation threshold, and gauge factor with sensing stability and damage evolution.
J. M. Parente, J. Nunes‐Pereira, A. P. Silva, P. N. B. Reis   +3 more
wiley   +1 more source