Results 181 to 190 of about 503,675 (296)

Thermomechanical Fatigue and Creep–Fatigue Interaction of Inconel 718 Additively Manufactured by Laser Beam Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth, Tomáš Babinský, Jan Lars Riedel, Wen Hao Kan, Aijun Huang, Martin Heilmaier, Ivo Šulák   +6 more
wiley   +1 more source

CX3CR1: a potential microglia-specific PET imaging target in Alzheimer's and Parkinson's diseases. [PDF]

Front Pharmacol
Yang H, Wang Y, Xu Y, Wang C.
europepmc   +1 more source

On the Influence of Antioxidants and Recycled MgO–C Source Material on the Mechanical Properties of Carbon‐Bonded Magnesia Refractories

Advanced Engineering Materials, EarlyView.
The presented study focuses on the fracture behaviour of carbon‐bonded magnesia MgO–C refractories, where environmentally friendly fructose, collagen and lignin serve as temporary binding agents. The partial substitution of the source material with recycled MgO–C reduces the fracture resistance, which can be counteracted by the additional introduction ...
Marc Neumann, Tom Weber, Jana Hubálková, Florian Kerber, Dinesh Kumar Gunasekar, Hans Jelitto, Christos G. Aneziris   +6 more
wiley   +1 more source

Unveiling unified patterns in Alzheimer's disease subtypes: An SCCA clustering approach integrating PET imaging and genomics data. [PDF]

Imaging Neurosci (Camb)
Yang F, Maher M, Saxena R, Dutta J.
europepmc   +1 more source

Sol–Gel Derived Polymer Precursors for Stereolithography of ZrC

Advanced Engineering Materials, EarlyView.
ZrC is a critical material target for extreme temperature conditions. This report describes a protocol for preparing ZrC ceramics via stereolithography and examines the impact of the polymer matrix on carbothermal reduction and mechanical stability of 3D printed ZrC.
Charles J. Rafalko, Evelyn Wang, Michael A. Hickner   +2 more
wiley   +1 more source

A sstR2-targeted radiohybrid theranostic agent for PET imaging and β^- therapy with excellent preclinical performance. [PDF]

Npj Imaging
Deiser S, Fenzl S, König V, Inoue S, Casini A.   +4 more
europepmc   +1 more source

Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics

Advanced Engineering Materials, EarlyView.
Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost, Lionel Presmanes, Soléna Colin, Marie Vidal, Sophie Guillemet‐Fritsch   +4 more
wiley   +1 more source

The application and prospect of granzyme B-targeted PET imaging in cancer immunotherapy. [PDF]

J Transl Med
Tong X, Jiang Y, Bi N.
europepmc   +1 more source

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

Integrating Multiparametric MRI and PSMA PET Imaging in Prostate Cancer: Toward a Unified Diagnostic and Risk-Stratification Paradigm. [PDF]

Medicina (Kaunas)
Pugliesi RA, Cannella R, Ben Mansour K, Di Biagio D, Alongi P.   +4 more
europepmc   +1 more source