Results 141 to 150 of about 14,471,209 (326)

Assessing the feasibility of integrating form-stable phase change material composites with cementitious composites and prevention of PCM leakage

, 2017
In this study, the feasibility of integrating form-stable phase change material (FS-PCM) composites into cementitious composites was investigated. Two different FS-PCM composites were fabricated by using paraffin as functional PCM and hydrophilic and ...
Wilson, John, Ramakrishnan, Sayanthan, Wang, Xiaoming, Sanjayan, Jay   +3 more
core   +1 more source

Determining the Relationship Between Composition, Structure, and Device Properties of GexSe1‐x‐Based Selector‐Only Memory

Advanced Electronic Materials, EarlyView.
Composition‐dependent structural evolution in GeXSe1‐X selector‐only memory (SOM) is correlated with device switching behavior. Increasing Ge strengthens network rigidity, suppresses atomic motion, and stabilizes threshold switching, while narrowing the memory window. The revealed structure–property relationship provides a guideline for compositionally
Tien Anh Nguyen, Changdeok Han, Dipannita Ghosh, Suyong Chae, Moongyu Choi, Sanghyun Ban, Myoungsub Kim, Sangmin Yoo, Seung Hwan Lee, Sieun Chae   +9 more
wiley   +1 more source

Enhancement of Dissymmetry Factors Through Axial Elongation of Hetero[n]helicenes

Angewandte Chemie, EarlyView.
A benzofuran scaffolding strategy enables the synthesis of hetero[9]‐, [12]‐, and [15]helicenes. Structural and chiroptical analyses demonstrate that systematic axial elongation increases helical distortion and significantly amplifies luminescence dissymmetry.
Jeppe S. Mogensen, Christoffer Bræstrup, Christoffer Warming, Georg I. Junker, Yann Lie, Mathias Hermann, Kurt V. Mikkelsen, Michael Pittelkow   +7 more
wiley   +2 more sources

New structure for better thermal resistance of building with phase change material: Response to milder thermal change than common walls

Case Studies in Thermal Engineering
By adding the insulation with phase change material (PCM), the building's thermal resistance was enhanced. Relying on the capabilities of DesignBuilder, 3584 different cases were defined to determine the effect of different input parameters on energy ...
Yan He, Shengnan Li, Mazeyanti Mohd Ariffin, Nidal H. Abu-Hamdeh, Arash Karimipour, Randa I. Hatamleh, PHH Viet, Aliakbar Karimipour   +7 more
doaj   +1 more source

Core and π‐Bridge Engineering to Deconstruct Y6‐Series into Modular Non‐Fused Acceptors: DFT‐Guided Structure‐Property Map for Organic Solar Cells

Advanced Electronic Materials, EarlyView.
The rigid fused backbone of Y6‐series acceptors is deconstructed into a modular, non‐fused A‐π‐A′‐π‐A architecture. Comprehensive quantum chemical simulations reveal that strategic core and π‐bridge engineering preserves strong near‐infrared light‐harvesting and enhances intramolecular charge‐transfer character.
Qurat ul Ain, Waqas Akram, Hasan Yaqoob, Munazza Shahid, Abdul Majid, Muhammad Altaf, Christian B. Nielsen, Raja Shahid Ashraf   +7 more
wiley   +1 more source

Evidence for a Cu(II)‐Catalysed CuAAC Reaction: A Combined Experimental and Computational Study

Angewandte Chemie, EarlyView.
A new mechanistic pathway for the CuAAC reaction has been found to operate under specific reaction conditions. The pathway is catalysed by Cu(II) through a self‐assembled dinuclear Cu(II) complex that incorporates the triazole product. Computational analysis and assessment of generality are reported.
Matthew J. Andrews, Thomas M. Richardson, Dean D. Roberts, Aitor Maestro, Timothy A. Hilton, Lia Sotorrios, Carlos Martín‐Fernández, Luca Craciunescu, Frederik Peschke, Aidan P. McKay, Stuart A. Macgregor, Glenn A. Burley, Allan J. B. Watson   +12 more
wiley   +2 more sources

A study on thermal characteristics of phase change material (PCM) in gypsum board for building application

, 2005
Using fatty acids as phase change materials (PCMs), it is possible to store a large amount of thermal energy in a small mass and with a narrow temperature transition.
Chuah, T. G., D., Rozanna, Ahmad, Salmiah, R., Medyan, Choong, Thomas S. Y., M., Sa'ari   +5 more
core   +1 more source

Safety of Sodium‐Ion Batteries: Evaluation and Perspective from Component Materials to Cells, Modules, and Packs

Advanced Energy Materials, EarlyView.
This review provides a bottom‐up evaluation of sodium‐ion battery safety, linking material degradation mechanisms, cell engineering parameters, and module/pack assembly. It emphasizes that understanding intrinsic material stability and establishing coordinated engineering control across hierarchical levels are vital for preventing degradation coupling ...
Won‐Gwang Lim, Seoa Kim, Erik A. Wu, Darren H. S. Tan, Shawn Peng, Xiaolin Li   +5 more
wiley   +1 more source

Hydration‐Gated Photoinduced Electron Transfer in BODIPY Dyes

Angewandte Chemie, EarlyView.
Hydration switches photoinduced electron transfer (PET) ON in alkoxy‐coordinated BODIPY dyes via specific hydrogen bonding. This gating yields a fluorescence lifetime span of ∼6 ns, enabling fluorescence lifetime imaging microscopy (FLIM) contrast in live cells and organoids. ABSTRACT Fluorescent probes based on photoinduced electron transfer (PET) are
Venkata N. K. Mamillapalli, Irina A. Okkelman, Fatima Akhssas, Greta Sambucari, Angela C. Debruyne, Dinesh Beniwal, Christophe Bucher, Mariangela Di Donato, Ruslan I. Dmitriev, Mikhail A. Filatov   +9 more
wiley   +2 more sources

Heat transfer performance of Li-ion battery pack using composite phase change material A review

Journal of Thermal Engineering
Electric Vehicles (EVs) rely on Li-ion batteries (Li-ion), which perform best in an operating temperature range of 15ÅãC to 40ÅãC. However, in regions where ambient temperatures are higher, EVs can catch fire even with thermal management systems.
Vinayak T. MANDLIK, Sandipkumar SONAWANE, Milind PATIL   +2 more
doaj   +1 more source