Results 41 to 50 of about 76,330 (257)

Effect of different adhesion strategies on fiber post cementation: Push-out test and scanning electron microscopy analysis

Contemporary Clinical Dentistry, 2013
Aim: The aim of this study was to investigate the effect of phosphoric acid etching and the dentin pre-treatment with sodium hypochlorite (NaOCl) on the push-out bond strength between fiber post and root canal dentin.
Letícia Oliveria Saraiva, Thaiane Rodrigues Aguiar, Leonardo Costa, Lourenço Correr-Sobrinho, Leonardo Muniz, Paula Mathias   +5 more
doaj   +1 more source

3D‐Printed Porous Hydroxyapatite Formed via Enzymatic Mineralization

Advanced Functional Materials, EarlyView.
Bone combines lightness, strength, and the ability to heal, inspiring new materials design. This work introduces a room‐temperature, enzyme‐mediated 3D printing method to create porous hydroxyapatite scaffolds. The process avoids energy‐intensive sintering, preserves bioactivity, and allows control over porosity and mineralization.
Francesca Bono, Anna Puiggalí‐Jou, Greta Cocchi, Mariangela Miccoli, Katharina Maniura‐Weber, Marcy Zenobi‐Wong, Esther Amstad   +6 more
wiley   +1 more source

An Engineered Living Material With Pro‐Angiogenic Activity Inducible by Near‐Infrared Light

Advanced Functional Materials, EarlyView.
NIR‐responsive engineered living materials (ELMs) for controlled angiogenesis: Near‐infrared (800 nm) light activates engineered probiotic bacteria within alginate‐based living materials to secrete a blood vessel‐regenerating protein. The released protein promotes pro‐angiogenic effects in endothelial networks and chick chorioallantoic membranes.
Anwesha Chatterjee, Stefanie S. M. Meier, Sara Trujillo, Andreas Möglich, Shrikrishnan Sankaran   +4 more
wiley   +1 more source

Use of acids as additives in sugarcane silage

Revista Colombiana de Ciencias Pecuarias, 2015
Background: sugarcane silage often becomes a problem for the producers due to its high population of yeast and its high content of soluble carbohydrates.
Eric HCB van Cleef, Anibal C Rêgo, René M Patiño, Flavia O Scarpino van Cleef, Jane MB Ezequiel   +4 more
doaj   +1 more source

Receptor‐Free Identification of Toxic Gases Enabled by Hygroscopic Aqueous Salt Films

Advanced Functional Materials, EarlyView.
Water as a gas sensor coating sounds impossible—until it stops evaporating. Here, hygroscopic salt solutions (LiCl, LiBr, H3PO4) form non‐drying aqueous films on CNT chemiresistors under ambient air. Gases partition into these liquid layers, sometimes transforming into water, and generate salt‐specific resistance fingerprints across a four‐channel ...
Seongwoo Lee, Yun‐Tae Kim, Hwarang Choi, Sanghwan Park, Seongyeop Lim, Chang Young Lee   +5 more
wiley   +1 more source

Copper removal using acid activated peanut husk from aqueous solution

Journal of Environmental Engineering and Landscape Management, 2016
Peanut husk, an agricultural waste is a precursor biomass veteran for chemical activation using phosphoric acid. The work deals with activation of peanut husk using phosphoric acid followed by its application.
Pradnya K. Ingle, Attarkar Karishma, Virendra K. Rathod   +2 more
doaj   +1 more source

Single‐ and Dual‐Atom Configurations in Atomically Dispersed Catalysts for Lithium–Sulfur Batteries

Advanced Functional Materials, EarlyView.
Single‐atom and dual‐atom‐based atomically dispersed catalysts (ADCs) effectively address the shuttle effect and sluggish redox kinetics in Li–S batteries. With nearly 100% atomic utilization and tunable coordination environments, ADCs enhance LiPSs adsorption, lower conversion barriers, and accelerate sulfur redox reactions.
Haoyang Xu, Zhenfeng Li, Yue Fei, Ali Mohammadi, Ge Li   +4 more
wiley   +1 more source

Establishing a Model Precursor System: Over a Decade of Research on Carbon Dots from the Citric Acid‐Urea System

Advanced Functional Materials, EarlyView.
The citric acid/urea (CA‐Urea) precursor system offers a versatile, scalable route to carbon dots with tunable luminescence and multifunctionality. Mechanistic insights into precursor chemistry and reaction parameters have enabled doping, surface modification, and hybridization strategies, yielding CDs for luminescent devices, sensing, catalysis ...
Yupeng Liu, Zhiqi Cai, Xiangxin Sun, Hanyi Zhang, Yiming Hao, Jun Wu, Zekun Yan, Xue Wu, Yiqi Liang, Liming Wang, Songnan Qu   +10 more
wiley   +1 more source

Interfacial Modulation for High‐Efficiency Large‐Area Organic Photovoltaics and Perovskite‐Organic Tandem Solar Modules

Advanced Functional Materials, EarlyView.
Self‐assembled monolayers (SAMs) are promising hole‐transporting materials for organic photovoltaics (OPVs), but suffer from self‐aggregation and poor large‐area uniformity. We find that interfacial modification using nicotinic hydrazide can eliminate the residual SAM aggregates by forming energetically favorable complexes, yielding uniform SAM.
Seongwon Yoon, Kangsik Cho, Sungmin Park, Kyeongmin Kim, Hyungju Ahn, Junhyeong Kim, Ahyeon Jin, Uijoon Lee, Yoon Hee Jang, Yongseok Jun, Hae Jung Son   +10 more
wiley   +1 more source

Multi‐Scale Interface Engineering of MXenes for Multifunctional Sensory Systems

Advanced Functional Materials, EarlyView.
MXenes, as two‐dimensional transition metal carbides and nitrides, demonstrate remarkable capabilities for multifunctional sensing applications. This review systematically examines multi‐scale interface engineering approaches that enhance sensing performance, enable diverse detection functionalities, and improve system‐level compatibility in MXene ...
Jiaying Liao, Sin‐Yi Pang, Jianhua Hao
wiley   +1 more source