Results 81 to 90 of about 7,192 (240)
A Practical Noise2Noise Denoising Pipeline for High‐Throughput Raman Spectroscopy
Advanced Engineering Materials, EarlyView.A lightweight and reproducible denoising pipeline for high‐throughput Raman spectroscopy is introduced, based on a 1D convolutional autoencoder trained with a Noise2Noise strategy. Using only repeated short‐exposure acquisitions, the method suppresses stochastic noise without reference spectra, enabling reliable spectral reconstruction while preserving
David Martin‐Calle +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The community‐driven Platform MaterialDigital Core Ontology (PMDco) 3.0 is introduced as a Basic Formal Ontology‐aligned semantic backbone for the processing–structure–properties paradigm in Materials Science and Engineering. Modular engineering, automated releases, and validation workflows are highlighted and key semantic patterns for materials ...
Markus Schilling +15 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees +6 more
wiley +1 more source
Entropy‐Driven Design of Low‐Melting‐Point Alloys via Compositionally Complex Strategy
Advanced Engineering Materials, EarlyView.Conventional low‐melting‐point alloys (LMPAs) are limited by a narrow compositional space and inherent property trade‐offs. This review presents an entropy‐driven design strategy that overcomes these limitations, ushering in a new class of low‐melting‐point compositionally complex alloys (LMCCAs).
Yinghui Shang +6 more
wiley +1 more source
Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning
Advanced Engineering Materials, EarlyView.The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley +1 more source
Instrumentation And Techniques In High Energy Physics
This book provides an introduction of some of the technology and techniques of modern particle physics. Each chapter is a deep dive into the relevant subject, which includes silicon pixel detectors, plastic scintillator in a high radiation environment ...
core +1 more source
Research on particle imaging detectors
, 1995 Much instrumentation has been developed for imaging the trajectories of elementary particles produced in high energy collisions. Since 1968, gaseous detectors, beginning with multiwire chambers and drift chambers, have been used for the visualisation of ...
Charpak, Georges
core +1 more source
Investigating the Low‐Temperature Phase Stability of the Binary Ta–W System
Advanced Engineering Materials, EarlyView.Atomistic simulations show that the binary Ta–W system forms ordered intermetallic phases, B2‐TaW and D03‐TaW3, as 0 K ground states. Configurational entropy, however, lowers the free energy of the disordered bcc solid solution, which becomes the stable phase above about 400 K.
Klemens Lechner +7 more
wiley +1 more source
Test of Diamond sCVD Detectors at High Flux of Fast Neutrons
We have tested the performance of spectroscopic single-crystal Chemical Vapor-Deposited (sCVD) diamond detectors with radioactive sources and with a pulsed deuterium-tritium neutron generator.
Asher Shor +2 more
core +1 more source
A Novel Approach to Estimate the Transition Temperature via Dynamic Nanoindentation
Advanced Engineering Materials, EarlyView.A new dynamic nanoindentation‐based method was developed that uses the stiffness ratio as an indicator of the elastic–plastic deformation contributions at different temperatures. The approach successfully identified transition temperatures in ferritic steel and distinguished them from continuously ductile austenitic steel.
Stefan Zeiler +4 more
wiley +1 more source