Results 31 to 40 of about 276,639 (273)

Enhanced piezoelectricity in 0.7BiFeO3-0.3BaTiO3 lead-free ceramics: Distinct effect of poling engineering

Journal of Materiomics, 2023
BiFeO3-BaTiO3 based ceramics are considered to be the most promising lead-free piezoelectric ceramics due to their large piezoelectric response and high Curie temperature.
Aizhen Song, Yu-Cheng Tang, Hezhang Li, Ning Wang, Lei Zhao, Jun Pei, Bo-Ping Zhang   +6 more
doaj   +1 more source

EFFECT OF TEMPERATURE ON DIELECTRIC, FERROELECTRIC, AND PIEZOELECTRIC PROPERTIES OF KNLNS-BNKZ CERAMICS

Tạp chí Khoa học Đại học Đà Lạt, 2021
Traditional ceramic technology combined with a two-step sintering technique has been applied to prepare 0.96(K0.48Na0.48Li0.04)(Nb0.95Sb0.05)O3-0.04Bi0.5(Na0.82K0.18)0.5ZrO3 (KNLNS-BNKZ) piezoelectric ceramics.
Phan Dinh Gio, Bui Thi Tuyet Nhung
doaj   +1 more source

Structure, Electrical Properties, and Thermal Stability of the Mn/Nb Co-Doped Aurivillius-Type Na_0.5Bi_4.5Ti₄O₁₅ High Temperature Piezoelectric Ceramics

Crystals, 2023
In order to meet the urgent need for high temperature piezoelectric materials with a Curie temperature over 400 °C, the Mn/Nb co-doped strategy has been proposed to improve the weak piezoelectric performance of the Aurivillius-type Na0.5Bi4.5Ti4O15 (NBT)
Tianlong Zhao, Kefei Shi, Chunlong Fei, Xinhao Sun, Yi Quan, Wen Liu, Juan Zhang, Xianying Dai   +7 more
doaj   +1 more source

Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying

Advanced Engineering Materials, EarlyView.
An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara, Vincent Rat, Quentin Dubreuil, Patrice Valorge, Simon Goutier, Alain Denoirjean, Olivier Messe, Céline Ruelle, Jean‐Philippe Poli   +8 more
wiley   +1 more source

Study on the heating law of thermal effect of HIFU on tissue based on piezoelectric ceramic voltage and vibration frequency

Scientific Reports
When high-intensity focused ultrasound (HIFU) is used to heat human tissues during surgery, shortening the heating time and increasing the heating rate are crucial for implementing surgery.
Yuping Long, Yi Gan, Fujia Sun, Yansong Zhao   +3 more
doaj   +1 more source

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

Unveiling the mechanism of substitution-induced high piezoelectric performance in PLZT ceramics

Journal of Advanced Ceramics
Ferroelectric lead zirconate titanate (PZT, PbZr1−xTixO3) dominates the piezoelectric ceramic market because of its high piezoelectric coefficient, high thermal stability and low processing cost.
Ciaran Joseph O’Malley, Xuyao Tang, Vladimir Koval, Kan Chen, Zixuan Wu, Krishnarjun Banerjee, Wanting Hu, Haixue Yan   +7 more
doaj   +1 more source

Structure, dielectric and piezoelectric properties of Pb[(Zr0.45,Ti0.5)(Mn0.5,Sb0.5)0.05]O3 ceramics [PDF]

Processing and Application of Ceramics, 2020
This study describes structure, dielectric and piezoelectric properties of Pb[(Zr0.45,Ti0.5)(Mn0.5,Sb0.5)0.05]O3 (PZT-PMS) ceramics prepared by conventional mixed-oxide route and sintered at up to 1180 °C. The prepared ceramics was characterized by X-ray
Louanes Hamzioui, Fares Kahoul, Ahmed Boutarfaia, Abderezak Guemache, Michel Aillerie   +4 more
doaj   +1 more source

Analyses of power output of piezoelectric energy-harvesting devices directly connected to a load resistor using a coupled piezoelectric-circuit finite element method [PDF]

, 2009
A coupled piezoelectric-circuit finite element model (CPC-FEM) is proposed for the first time to study the power output of a vibration-based piezoelectric vibration-based piezoelectric energy harvesting devices (EHDs) that is directly connected to a ...
Zhu, Meiling, Njuguna, James A. K., Worthington, Emma   +2 more
core   +1 more source

Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials

Advanced Engineering Materials, EarlyView.
Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley   +1 more source