Results 31 to 40 of about 28,804 (233)

Ultrasound Corrosion Mapping on Hot Stainless Steel Surfaces

Metals
This study investigates the application of Phased Array Corrosion Mapping (PACM) as a non-destructive testing (NDT) method for detecting and monitoring corrosion growth on hot stainless steel (SS) surfaces, specifically focusing on SS 304 and SS 316 ...
Jan Lean Tai, Mohamed Thariq Hameed Sultan, Farah Syazwani Shahar, Andrzej Łukaszewicz, Zbigniew Oksiuta, Rafał Grzejda   +5 more
doaj   +1 more source

In Situ Diagnosis of a Gear-Tooth Surface Damage Using Laser Scattering

Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2011
We propose herein an in situ method to remotely diagnose gear-tooth damage using scattering of a laser beam. The proposed method provides early and accurate diagnosis of the gear-tooth-surface condition.
Eiichirou TANAKA, Kazuteru NAGAMURA, Kiyotaka IKEJO, Ryozo NEMOTO   +3 more
doaj   +1 more source

Effect of Laser Surface Melting on Chromium Carbide of 304 Stainless Steels [PDF]

Engineering and Technology Journal, 2018
In the present study, the effects of laser surface melting (LSM) on chromium carbide of heat treated (AISI 304) austenitic stainless steels (ASS) was studied with the aim to suppress sensitization of 304SS. Austenitic stainless steels were heated (aging)
Sami Jafar, Mohammad Kadhim, Sameer Faayadh   +2 more
doaj   +1 more source

Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution

Advanced Engineering Materials, EarlyView.
Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat, Hamidreza Enshaei, Elaine Armelin, José I. Iribarren, Antonio Mateo, Miguel Morales   +5 more
wiley   +1 more source

Assessing the Corrosive Effects of Unmelted Particles in Additively Manufactured Ti6Al4V: A Study in Simulated Body Fluid

Alloys
This study investigates the corrosion behavior of Grade 23 Ti6Al4V alloys produced through laser powder bed fusion (L-PBF) when exposed to simulated body fluid at room temperature, focusing on the role of unmelted particles.
Surinder Pal, Xavier Velay, Waqas Saleem
doaj   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Tribological Performance of 60NiTi Alloy Under Varying Contact Conditions and Elevated Temperatures in Linear Reciprocating Sliding

Advanced Engineering Materials, EarlyView.
This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani, Miguel Angel Selles, Maziar Ramezani   +2 more
wiley   +1 more source

Corrosion Fatigue Analysis in Power Steam Turbine Blade

Metals, 2023
The corrosion fatigue behavior of a martensitic stainless steel AISI 410 with 12% Cr, used in the fabrication of steam turbine blades at low pressure (L-P), was studied using the electrochemical noise technique (EN) under mechanical fatigue (immersion ...
José Alfredo Rodrígez Ramírez, Christian Marisol Clemente Mirafuentes, Manuela Alejandra Zalapa Garibay, Juan C. García Castrejón, Luis Gonzalo Guillén Anaya   +4 more
doaj   +1 more source

EBSD Study of Creep‐Induced Lattice Misorientation in MgO‐Particle‐Reinforced Austenitic Steel Composites

Advanced Engineering Materials, EarlyView.
Creep experiments at 900°C on coarse‐grained steel‐ceramic composites containing recycled magnesia reveal that higher ceramic volume fractions significantly enhance the creep resistance. Detailed EBSD investigations identify subgrain formation in the steel matrix as the dominant deformation mechanism.
Moritz Müller, Amaya Compart, Mahnaz Mehdizadehlima, Serhii Yaroshevskyi, Christos G. Aneziris, Horst Biermann, Anja Weidner   +6 more
wiley   +1 more source

Nanoindentation Criteria for Combinatorial Thin Film Libraries

Advanced Engineering Materials, EarlyView.
Thin‐film material libraries are compositional spreads used for screening composition‐structure‐property relationships. Nanoindentation is often used to characterize mechanical behavior across these systems, however variations in methodology are widespread.
Andre Bohn, Adie Alwen, Andrea M. Hodge
wiley   +1 more source