Results 241 to 250 of about 1,379,637 (289)
Advanced Materials Interfaces, EarlyView.3D DLP printed materials with porous bone structure. Preparation of new photocurable resin with a high content of ZrO2 NPs. Optimization of 3D printing parameters in DLP technology. 3D printing of polymer nanocomposites with very high resolution and low polymerization shrinkage. Obtaining ceramic materials by thermal treatment.
Klaudia Trembecka‐Wójciga +7 more
wiley +1 more source
Advanced Materials Interfaces, EarlyView.By directly comparing the impact of dual interfacial passivation by ammonium‐, sulfonium‐ and sulfoxonium‐based cations on the performance and stability of triple cation metal halide perovskite solar cells, it is found that it is the exact molecular structure of the cation, rather than the nature of the onium that influences the efficacy of passivation
Oscar Telschow +9 more
wiley +1 more source
Advanced Materials Interfaces, EarlyView.Nano‐octahedron Co3O4 decorated graphene composite electrode for selective and simultaneous detection of dopamine. The detection limit of 0.09 µM, and linear range from 1 to 500 µM are reported. The synergistic effect of nano octahedron Co3O4 and graphene results in excellent performance of the sensor in terms of selectivity and sensitivity.
Swathi Tharani Dharmalingam +5 more
wiley +1 more source
Spatially Controlled 3‐D Multiplexed Aptamer Patterning in Hydrogels
Advanced Materials Interfaces, EarlyView.A hydrogel platform based on norbornene‐functionalized polyvinyl alcohol enables high‐resolution, 3‐D multiplexed patterning of DNA aptamers via two‐photon polymerization. Two distinct aptamers are covalently immobilized with single micron‐scale precision across the x, y, and z dimensions.
Kevin Roost +9 more
wiley +1 more source
Advanced Materials Interfaces, EarlyView.Polyvinyl pyrrolidone passivation enhances TiO2/CsPbI2Br interfaces, suppressing recombination and improving photodetector performance with faster response, higher photoresponsivity, and superior detectivity. Abstract Inorganic perovskites hold immense promise for optoelectronic applications, but their performance is often hindered by defects and trap ...
Shruti Shah +12 more
wiley +1 more source
Advanced Materials Interfaces, EarlyView.Detecting single molecules on large interfaces is challenging due to minimal perturbations on the sensing surface. Some biological systems achieve this feat using amplification mechanisms, but their molecular foundations remain unclear. To investigate, a Design of Experiments (DoE) approach examines how pH and ionic strength in conditioning solutions ...
Michele Catacchio +9 more
wiley +1 more source
Advanced Materials Interfaces, EarlyView.Laser structuring of biocompatible polymers creates precise surface patterns that influence cell organization. By imaging, contact angle measurements, and chemical analysis, this study demonstrates the ability of laser‐induced micro‐structured surfaces to guide muscle cell alignment. These findings support laser patterning of biopolymers as a promising
Clarissa Murru +7 more
wiley +1 more source
Advanced Materials Interfaces, EarlyView.Nitrogen doping on Ru(0001) is investigated using ion implantation and annealing, tuning the distribution of graphitic (GN) and pyridinic (PN) nitrogen sites. STM, XPS, and DFT identified the structure and site distribution, and a thermodynamic phase diagram showed that GN is most stable at the Atop region, while PN preferred boundaries between FCC and
Buddhika S. A. Gedara +8 more
wiley +1 more source
Experimental Study of Gas Microbubbles on Oil‐Infused Wrinkled Surfaces
Advanced Materials Interfaces, EarlyView.Microbubbles are observed on both superhydrophobic (SHS) and lubricant‐infused surfaces (LIS) immersed to gassed water. The bubbles on LIS are stabilized by the lubricant cloaking layer, while bubbles on SHS shrink vertically over the same time frame.
Leo James +4 more
wiley +1 more source
Advanced Materials Interfaces, EarlyView.The present work is concerned with the fabrication of CO2 sensors based on MWCNTs/ZnO material, which is obtained by RF magnetron sputtering and electron‐beam deposition methods. The sensor exhibits highly sensitive and selective behavior, high repeatability, and temporal stability at low CO2 concentrations.
Mikayel Aleksanyan +6 more
wiley +1 more source