Results 111 to 120 of about 7,352 (265)
High‐Performance Recycling Biobased Photopolymers for 3D Printing
Advanced Science, EarlyView.By using biobased phenols like eugenol, novel biobased photopolymers containing dissociative phenol‐carbamate bonds are designed for 3D printing. Meanwhile, a “mixed‐monomer assisted recycling” strategy is proposed to recycle the materials. The resulting materials not only achieve high‐performance and excellent chemical recyclability simultaneously ...
Hang Zhou +12 more
wiley +1 more source
Planetary Boundary Layer Modeling and Standard Provisions for Supertall Building Design. [PDF]
J Struct Eng (N Y N Y), 2017 Simiu E, Heckert NA, Yeo D.
europepmc +1 more source
Improved Direct Ink Writing of Liquid Metal Foams via Liquid Additives
Advanced Electronic Materials, EarlyView.The ability to pattern liquid metal is useful for making soft electrical and thermal devices. Dispensing liquid metal from a nozzle naturally results in the formation of spheroidal droplets, making direct‐write printing challenging. Liquid metal foams containing pockets of air can extrude as filaments, albeit inconsistently.
Febby Krisnadi +3 more
wiley +1 more source
Advanced Electronic Materials, EarlyView.This tutorial introduces a practical framework for implementing early‐stage Life‐Cycle Assessment (LCA) in flexible and printed electronics. Using organic electrochemical transistors (OECTs) as a case study, the modular Process‐of‐Record and open‐access inventory provides a rich resource adaptable to a plethora of technologies in printed electronics ...
Laura Teuerle +6 more
wiley +1 more source
Conformal Reconfigurable Intelligent Surfaces: A Cylindrical Geometry Perspective
Advanced Electronic Materials, EarlyView.Cylindrical reconfigurable intelligent surfaces are explored for low‐complexity beam steering using one‐bit meta‐atoms. A multi‐level modeling approach, including optimization‐based synthesis, demonstrates that even minimal hardware can support directive scattering.
Filippo Pepe +4 more
wiley +1 more source
Advanced Energy Materials, EarlyView.Boron‐oxide‐assisted particle engineering stabilizes O3‐type layered cathodes for sodium‐ion batteries by mitigating phase transitions and lattice strain. Acting as flux and structural modifier, boron forms submicron hexagonal platelets with (003) facets and expanded Na‐layer spacing, enabling rapid Na⁺ diffusion and mechanical resilience.
Tengfei Song +9 more
wiley +1 more source
Advanced Energy Materials, EarlyView.A fluorinated cyclic ether, FDOL, is shown to stabilize Mg metal anodes by tuning Mg2+ solvation of the G2 electrolyte. The G2‐FDOL electrolyte suppresses passivation and thick, diffusion‐blocking Mg deposits, enabling more uniform Mg plating/stripping and sustained interfacial reactions.
Hafiz Ahmad Ishfaq +9 more
wiley +1 more source
Advanced Energy Materials, EarlyView.Trace water is acting as a constructive mediator in 2LiCl–GaF3, markedly increasing ionic conductivity while reorganizing local coordination. Hydration creates localized Li+ solvation environments and partially dissociates ion pairs, enhancing Li‐ion mobility.
Youngkyung Kim +10 more
wiley +1 more source
Predicting Performance of Hall Effect Ion Source Using Machine Learning
Advanced Intelligent Systems, Volume 7, Issue 3, March 2025.This study introduces HallNN, a machine learning tool for predicting Hall effect ion source performance using a neural network ensemble trained on data generated from numerical simulations. HallNN provides faster and more accurate predictions than numerical methods and traditional scaling laws, making it valuable for designing and optimizing Hall ...
Jaehong Park +8 more
wiley +1 more source
Isotopic Constraints on SO<sub>2</sub> Oxidation Rates and Their Potential Relationship with Sulfate Formation Pathways in the Planetary Boundary Layer. [PDF]
ACS Environ AuNiu Z, Lin M.
europepmc +1 more source