Results 21 to 30 of about 672,110 (301)

Case Study on the Effect of Delay-Time Differences between Columns during Blasting Demolition of RC Structures with a Small Height-to-Width Ratio

open access: yesApplied Sciences, 2023
Blasting demolition plays an important role in building demolition, and numerical-simulation methods can facilitate the optimization of blasting-demolition schemes.
Wenle Gao   +4 more
doaj   +1 more source

Simplified Plastic Hinge Model for Reinforced Concrete Beam–Column Joints with Eccentric Beams

open access: yesApplied Sciences, 2021
In nonlinear analysis for performance-based design of reinforced concrete moment frames, a plastic hinge spring element is predominantly used in order to simply and accurately describe the inelastic behavior of beam–column joints, including strength ...
Hyeon-Jong Hwang, Chang-Soo Kim
doaj   +1 more source

INFLUENCE OF PANEL ZONE SIZES ON ULTIMATE BEARING CAPACITY OF H-SHAPED STEEL FRAMES [PDF]

open access: yesCivil Engineering Journal, 2019
In order to explore the influence of panel zone sizes on the ultimate bearing capacity of H-shaped steel frames, this study examines a steel frame structure with cross-shaped sections consisting of beams, columns and panel zones based
Yan Zhang   +3 more
doaj   +1 more source

Progressive collapse of reinforced concrete buildings considering flexure-axial-shear interaction in plastic hinges

open access: yesCogent Engineering, 2021
Progressive collapse assessment of a reinforced concrete (RC) building designed only for gravity loads and lacking a dedicated lateral load resisting system was carried out using the alternate load path (ALP) method and finite element method (FEM ...
Meshal A. Abdulsalam   +1 more
doaj   +1 more source

Generalized finite element formulation for efficient first-order plastic hinge analysis

open access: yesAdvances in Mechanical Engineering, 2019
This article presents generalized finite element formulation for plastic hinge modeling based on lumped plasticity in the classical Euler–Bernoulli beam.
Dae-Jin Kim   +3 more
doaj   +1 more source

The Effect of Plastic Hinge Location on the Flexural Strength Demand of Welded Flange Plate Connections

open access: yesElectronic Journal of Structural Engineering, 2019
A Welded Flange Plate (WFP) connection consists of top and bottom flange plates that are fillet welded to the flanges of a beam and are complete joint penetration groove welded to a column flange.
J. Kent Hsiao   +3 more
doaj   +1 more source

Plastic Hinge Length of UHPC-NC Hybrid Pier Reinforced by High-strength Steel Bars [PDF]

open access: yesZhengzhou Daxue xuebao. Gongxue ban, 2023
To discuss the plastic deformation ability of UHPC-NC hybrid pier reinforced by high-strength steel bars, a ductility analysis model was established and calibrated by the corresponding pseudo-static test of concrete piers strengthened with different ...
REN Liang   +3 more
doaj   +1 more source

Numerical Study on the Sagging Damage of the Simplified Hull Girder Subjected to Underwater Explosion Bubble

open access: yesApplied Sciences, 2023
The pulsation of the bubbles resulting from underwater explosions can lead to severe damage to the structure of the ship’s hull, and even to its sinking.
Yuxiang Gong   +3 more
doaj   +1 more source

Lateral Deformation Capacity and Plastic Hinge Length of RC Columns Confined with Textile Reinforced Mortar Jackets

open access: yesCivilEng, 2021
This paper presents a nonlinear finite element analysis (FEA) of textiles reinforced mortars (TRM)-confined reinforced concrete (RC) columns through jacketing, under combined axial and cyclic loadings.
Azadeh Parvin, Mohannad Alhusban
doaj   +1 more source

THE MODEL OF THE "INTERACTIVE PLASTIC HINGE" [PDF]

open access: yes, 1985
Instead of the plastic hinge the "interactive hinge" and "zone" have been introduced for a mounting base constructed from plates which are of a much higher degree of freedom than the previous ones as they also embrace the ...
Iványi, M.
core   +1 more source

Home - About - Disclaimer - Privacy