Results 201 to 210 of about 3,897,964 (375)

Study on the evolution and prevention of wellbore casing failure induced by marker bed water invasion. [PDF]

PLoS One
Miao X, Dong K, Li J, Yu D, Li T.
europepmc   +1 more source

Overall Equipment Effectiveness as a Strategic KPI in Intelligent Manufacturing: A Case Study in Plastic Injection Moulding [PDF]

Sonia Val Blasco, Nicolás Jiménez, María Pilar Lambán   +2 more
openalex   +1 more source

Fabrication of Aligned Polycaprolactone Nanofibrillar Bundles to Control Cell‐Mediated Collagen Deposition in Engineered Cartilage

Advanced Materials, EarlyView.
Melt electrofibrillation (MEF) enables the fabrication of nanofibrillar PCL scaffolds with defined architectures that guide cellular alignment and retention during cartilage tissue engineering. Unlike conventional melt electrowriting, MEF consistently directs collagen type II‐rich extracellular matrix organization, providing a tunable platform to ...
Alba Pueyo Moliner, Lennard Spauwen, James L. Martin Robinson, Ángela García Grech, Isabelle Martinier, Sara Grasselli, Aylin Kara Özenler, Matthias Ryma, Jürgen Groll, Mylène de Ruijter, Jos Malda   +10 more
wiley   +1 more source

Investigation of crack initiation, and mechanical behavior of polypropylene and polymer-based composites under plastic deformation in automotive brake fluid reservoirs. [PDF]

PLoS One
Jian Chun L, Quanjia Y, Bin Y, Debing Z, Sen Z, Wang K, Raza A, Haris M, Hussain J.   +8 more
europepmc   +1 more source

Introduction to Plastic Injection Molds

Transactions of Materials Processing, 2002
openaire   +2 more sources

In Situ Formation of a Highly Selective Nickel Single Atom Catalyst for Electrochemical CO2 Reduction to CO

Advanced Materials, EarlyView.
Development of a novel method for synthesizing Ni single atom catalysts for highly selective electrochemical CO2 reduction in situ. This catalyst achieves 100% selectivity for CO and is formed in an industrially relevant cell architecture. Using post‐mortem XRD, STEM, and EDS and operando XAS, the identity of the active site and the mechanism behind ...
Ian Street, Venkata Sai Sriram Mosali, Noah Sandberg, Fengyuan Shi, Deborah Myers, William E. Mustain   +5 more
wiley   +1 more source

Three-stage V-line Technique with Polycaprolactone Filler for Facial Contour Restoration. [PDF]

Plast Reconstr Surg Glob Open
Chen W, Cui H.
europepmc   +1 more source

Reducing Interfacial Separation Force in High‐Speed Constrained‐Surface Projection Stereolithography Using a Dual‐Modulus Silicone Release Film

Advanced Materials Interfaces, EarlyView.
A dual‐modulus silicone release film creates distributed stress concentrations at high‐/low‐modulus boundaries, triggering multi‐site crack initiation and rapid interfacial detachment. The architecture lowers the peak separation force by 97.6%, shortens detachment time, and enables stable continuous projection stereolithography at 720 mm h−1, offering ...
Xiaogang Li, Xiaoqing Kang, Hong Xiao, Yugang Duan   +3 more
wiley   +1 more source

Efficacy of Subcutaneous Kenacort Injection for Trigger Finger: A Retrospective Analysis. [PDF]

Plast Reconstr Surg Glob Open
AlBahlal A, Gabr M, Alsubhi MN, Alosaimi K, Alghamdi AM, Altalhah AM, Alshowih R, Al Madani J.   +7 more
europepmc   +1 more source

Optimising Injection Strategies and EGR in Modified Piston Diesel Engines Fuelled with Waste Plastic Oil [PDF]

Rajammagari Hussain Vali, Vemuri Sai Srikanth, Mohammad Mujtaba Ahmed, A. Gouse Peera, P. Srikar   +4 more
openalex   +1 more source