Results 41 to 50 of about 102,646 (304)
Effect of stem age on the response of stem diameter variations to plant water status in tomato [PDF]
, 2012 Plant water status plays a major role in glasshouse cultivation of tomato (Solanum lycopersicum L.). New climate control technologies alter the glasshouse climate and make it less dependent on solar radiation.
De Nayer, Frans +7 more
core +2 more sources
Advanced Engineering Materials, EarlyView.This study reports the fabrication of trabecular bioactive glass scaffolds (composition “1d”: 46.1SiO2‐28.7CaO‐8.8MgO‐6.2P2O5‐5.7CaF2‐4.5Na2O wt%) through vat photopolymerization and the relevant results from mechanical testing and in vivo implantation procedures in rabbit femora, showing great promise for bone tissue engineering applications.
Dilshat Tulyaganov +8 more
wiley +1 more source
Class I Gap-formation in Highly-viscous Glass-ionomer Restorations: Delayed vs Immediate Polishing [PDF]
, 2008 This in vitro study evaluated the effects of delayed versus immediate polishing to permit maturation of interfacial gap-formation around highly viscous conventional glass-ionomer cement (HV-GIC) in Class I restorations, together with determining the ...
Anusavice +28 more
core +1 more source
Advanced Engineering Materials, EarlyView.Microstructural evolution and hardness optimization along the cross‐section of friction stir welded AA6061/AlSi10MgMn joints, for electric vehicle battery housings, were investigated. Postweld aging between 170°C and 220°C enhances hardness uniformity within the nugget zone.
Emanuele Ghio, Emanuela Cerri
wiley +1 more source
Cigarette filter material and polypropylene fibres in concrete to control drying shrinkage [PDF]
, 2012 Due to a reduction in demand for cigarette filter material (North East UK), significant quantities have arisen that have little commercial value. The filter manufacturers have been looking for another outlet for their product and polypropylene fibre ...
Richardson, Alan
core
Analysis of optimal injection moulding process parameters for thin-shell plastic product using response surface methodology [PDF]
, 2014 The injection molding process is used to produce thin-walled plastic products for a wide variety of applications. However, the difficulty in adjusting optimum process parameters setting may cause defects on injected moulded parts such as shrinkage.
Awang Bono +2 more
core +1 more source
Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6
Advanced Engineering Materials, EarlyView.The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter +4 more
wiley +1 more source
Wellbore shrinkage during drilling in methane hydrate reservoirs
Energy Science & Engineering, 2019 Methane hydrates as a clean and abundant energy source, have attracted the attention of the world. However, the instability of hydrate reservoirs makes it difficult to drill production wells.
Chuanliang Yan +6 more
doaj +1 more source
Advances in Materials Science and Engineering, 2021 A plastic back door car panel was considered as the research object. In order to obtain optimal injection molding simulation parameters, Moldflow2018 is used to simulate injection molding process of plastic back door car panel.
Guoqing Wang, Youmin Wang, Deyu Yang
doaj +1 more source
Immediate versus water-storage performance of Class V flowable composite restoratives [PDF]
, 2006 Objectives The aims of this investigation were to clarify the effects of 24 h water-storage and finishing time on mechanical properties and marginal adaptation to a Class V cavity of eight modern flowable resin-composites.
Hatanaka, Kenji +3 more
core +1 more source