Advanced Engineering Materials, EarlyView.This study investigates the effects of milling parameters, including rotational speed, milling duration, and ball‐to‐powder ratio, on TiAl particle size and morphology in an XHV‐equivalent atmosphere. The creation of oxide‐free surfaces enhances the mechanical properties of green bodies.
Jytte Möckelmann +4 more
wiley +1 more source
Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing
Advanced Engineering Materials, EarlyView.The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai +6 more
wiley +1 more source
Extension of Flow Behaviour and Damage Models for Cast Iron Alloys with Strain Rate Effect
Chinese Journal of Mechanical EngineeringCast iron alloys with low production cost and quite good mechanical properties are widely used in the automotive industry. To study the mechanical behavior of a typical ductile cast iron (GJS-450) with nodular graphite, uni-axial quasi-static and dynamic
Chuang Liu +4 more
doaj +1 more source
Mechanical Engineering JournalMetallic materials are widely employed due to their exceptional mechanical attributes. Plastic deformation is a common issue that influences both the mechanical and electrical properties, with profound implications for the longevity of engineered ...
Guodong WANG +4 more
doaj +1 more source
Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A
Advanced Engineering Materials, EarlyView.The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han +5 more
wiley +1 more source
The Shear Stress Determination in Tubular Specimens under Torsion in the Elastic-Plastic Strain Range from the Perspective of Fatigue Analysis. [PDF]
Materials (Basel), 2020 Seyda J, Pejkowski Ł, Skibicki D.
europepmc +1 more source
Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites
Advanced Engineering Materials, EarlyView.Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter +9 more
wiley +1 more source
Influence of Plastic Strain Accumulation in Continuous Ingots during ECAP on Structure and Recrystallization Temperature of AlCu4MgSi Alloy. [PDF]
Materials (Basel), 2020 Nuckowski PM, Snopiński P, Wróbel T.
europepmc +1 more source
Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment
Advanced Engineering Materials, EarlyView.This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li +5 more
wiley +1 more source
Efektywne Obliczanie Rur Grubościennych w Przypadku Liniowego Wzmocnienia Plastycznego
Engineering Transactions, 1969 Making use of the integral equations of equilibrium for a thick-walled tube loaded by a pressure and an axial force, assuming incompressibility and linear strain hardening of the material, the strain regions of the tube are determined in a system of ...
J. Ryś
doaj