Research on J integral of Crack Tip on Intersecting Line of Fracturing Pump Head
Shiyou jixie, 2018 To address the primary failure modes of the fracturing pump head, a finite element model with different angular crack size is established. The J integral of the crack front and the plastic zone size of the crack tip are calculated.
Wei Chao, Zhou Sizhu, Hua Jian, Zhang Si
doaj
A Semi-Analytical Solution for Shock Wave Pressure and Radius of Soil Plastic Zone Induced by Lightning Strikes. [PDF]
Materials (Basel), 2022 Wu Z +5 more
europepmc +1 more source
Optical method for determination of the crack tip plastic zone sizes and shape in aluminum alloys [PDF]
, 2015 В статті запропонована оптична методика визначення розмірів та форми пластичних зон (ПЗ) тріщин по характерним змінам зображення поверхні металу поблизу тріщини, які спостерігаються з допомогою металографічного мікроскопу при його розфокусуванні.
Kosteniuk, D. +1 more
core
Microplastics from Wearable Bioelectronic Devices: Sources, Risks, and Sustainable Solutions
Advanced Functional Materials, EarlyView.Bioelectronic devices (e.g., e‐skins) heavily rely on polymers that at the end of their life cycle will generate microplastics. For research, a holistic approach to viewing the full impact of such devices cannot be overlooked. The potential for devices as sources for microplastics is raised, with mitigation strategies surrounding polysaccharide and ...
Conor S. Boland
wiley +1 more source
A contact problem aplication for the local behaviour of soil pile interaction [PDF]
, 2017 In geotechnical engineering, the main parameter for the performance of structures such as reinforced walls or deep foundations is often the shaft bearing capacity.
Baeßler, Matthias +4 more
core
Advanced Functional Materials, EarlyView.Lead halide perovskite nanocrystals are promising scintillators but suffer from reabsorption losses and limited compatibility with high‐Z additives. Hybridization of CsPbBr3 nanocrystals with PbBr2‐passivated HfO2 nanoparticle sensitizers, achieved during or after synthesis, produces stable composites with maintained optical quality, improved ...
Francesco Bruni +17 more
wiley +1 more source
In Situ Measurement of Cyclic Plastic Zone and Internal Strain Response of Q&P Steel near Fatigue Crack Tip Region Based on Micro-DIC. [PDF]
Materials (Basel), 2022 Gao H, Lin Z, Huang X, Shang H, Zhan J.
europepmc +1 more source
Interconnected Porous Hydrogels with Tunable Anisotropy Through Aqueous Emulsion Bioprinting
Advanced Functional Materials, EarlyView.A 3D bioprintable microporous bioink is developed using an aqueous two‐phase system (ATPS) composed of extracellular matrix (ECM) mimetic biopolymers. The ATPS bioink enables the fabrication of interconnected porous architectures with up to 70% porosity, supporting long‐term cell viability and 3D cell alignment, enabling a simultaneous generation of ...
Hugo Edgar‐Vilar +4 more
wiley +1 more source
Strain patterns and strain accumulation along plate margins [PDF]
Observations of strain accumulation along plate margins in Japan, New Zealand, and the United States indicate that: (1) a typical maximum rate of secular strain accumulation is on the order of 0.3 ppm/a, (2) a substantial part of the strain accumulation ...
Savage, J. C.
core +1 more source
Adaptive 4D‐Printed Vascular Stents With Low‐Temperature‐Activated and Intelligent Deployment
Advanced Functional Materials, EarlyView.Microarchitected coronary artery stents were fabricated using a polycaprolactone (PCL)‐based shape memory polymer (SMP) composite via projection micro‐stereolithography (PµSL) 4D printing. By incorporating diethyl phthalate (DEP) as a plasticizer, the thermal transition temperature (Ttran) was modulated to about 37°C, enabling rapid and autonomous ...
Yannan Li +12 more
wiley +1 more source