Results 141 to 150 of about 1,580 (218)

Modeling Dislocation Cutting of γ′ Precipitates in Ni‐Base Superalloys: Linking Atomistic and Dislocation Dynamics Simulations

Advanced Engineering Materials, EarlyView.
Dislocation cutting of γ′ precipitates in Ni‐based superalloys is investigated by linking atomistic simulations with discrete dislocation dynamics. The critical cutting stress is shown to be governed by the antiphase boundary energy, while line tension effects promote edge‐preferred cutting.
Frédéric Houllé, Siwen Gao, Marc Fivel, Anxin Ma, Daria Smirnova, Sriram Anand, Arun Prakash, Julien Guénolé, Alexander Hartmaier, Erik Bitzek   +9 more
wiley   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Triple Junctions as Dislocation‐Like Defects: The Role of Grain Boundary Crystallography Revealed by Experiment and Atomistic Simulation

Advanced Engineering Materials, EarlyView.
Grain boundary triple junctions are an essential ingredient of the microstructure of polycrystalline materials. In this study, a triple junction is observed using atomic‐resolution scanning transmission electron microscopy and characterized. Computer simulations reveal that the junction has a dislocation character that is determined by the joining ...
Tobias Brink, Saba Saood, Peter Schweizer, Jörg Neugebauer, Gerhard Dehm   +4 more
wiley   +1 more source

“Plastic Eyes” [PDF]

Clinical and Experimental Optometry, 1944
openaire   +2 more sources

Advanced Electron Microscopy and Microcomputed Tomography Analysis of Single‐Crystal Ni‐Base Superalloys After Short‐Term Multiaxial Creep

Advanced Engineering Materials, EarlyView.
This work studies the anisotropic behavior of circular notched tensile specimens of Ni‐base superalloy single crystals during high‐temperature tensile creep along [001], [110], and [111]. Correlative scale‐bridging imaging of specimens reveals early rupture along [110] because 1) plastic deformation proceeds faster at notch center; 2) more (brittle ...
Leonardo Agudo Jácome, Lijie Cao, Christoph Somsen, Johannes Boes, René Hesse, Werner Theisen, Gunther Eggeler   +6 more
wiley   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

External and Internal Cracking Caused by Heat Treatment in Laser Powder Bed Fusion‐Fabricated Inconel 738LC Components

Advanced Engineering Materials, EarlyView.
Manufacturing problems such as heat treatment‐induced cracking hinder the widespread application of the laser powder bed fusion (LPBF) process to superalloys. In this study, cracks in the LPBF components of Inconel 738LC superalloy are characterized after heat treatment at various temperature ranges, revealing two distinct cracking behaviors.
Kosuke Kuwabara, Masahiro Kusano, Ayako Ikeda, Toshio Osada, Makoto Watanabe   +4 more
wiley   +1 more source

Additive Manufacturing of Alumina‐Reinforced Elastomers

Advanced Engineering Materials, EarlyView.
Vat‐photopolymerized elastomers reinforced with platelet‐shaped alumina exhibited preferential orientation, reduced porosity, and significantly enhanced mechanical performance. A 3 wt% platelet loading increased tensile strength from 12.4 to 45.7 MPa, highlighting the critical role of filler morphology in elastomeric VPP composites.
Majid Barzegar Keyvani, Zongwen Fu, Robert Göstl, Hamed Shokri, Carmine Putignano, Gianluca Percoco, Bilal Gökce   +6 more
wiley   +1 more source

High‐Temperature Phase Transformation in a V‐9Si‐6.5B Alloy: The Kinetic and Crystallographic Pathway From V5SiB2 to V8SiB4

Advanced Engineering Materials, EarlyView.
In situ synchrotron high‐energy X‐ray diffraction reveals the real‐time high‐temperature phase evolution of a ternary V‐9Si‐6.5B alloy. The study uncovers a kinetically delayed V5SiB2 → V8SiB4 transformation governed by massive structural and chemical barriers.
Zahra Sabeti, Andreas Stark, Roja Rani Korrayi, Florian Pyczak, Georg Hasemann   +4 more
wiley   +1 more source

OntOMat: Toward Ontology‐Based Product and Process Design Engineering and Optimization Solutions Fueling Circular Value Chains

Advanced Engineering Materials, EarlyView.
The OntOMat ontology establishes a structured framework for polymer matrix fiber reinforced composite materials, integrating manufacturing processes, characterization methods, and multiscale design through the VDI/VDE 3682 formalized process description standard.
Nicolas Christ, Jörg Hohe, Martin Kördel, Michael Giese, Niklas Toffert, Christian Seidel, Olaf Rehme, Patrik Schneider, Oliver Focke, Elie Abi Aoun, Claas Falldorf, Beñat Gutierrez, Alexandra Kühn, Sven Torstrick-von der Lieth, Christoph Herden, Erik Johannsen, Jan‐Uwe R. Schmidt, Felix Winkelmann, Andreas Schott, Daniel Schott   +19 more
wiley   +1 more source