Results 111 to 120 of about 4,144,262 (288)
VI. On the influence of the ocean on the plumb-line in India [PDF]
Proceedings of the Royal Society of LondonAbstract This paper is a sequel to two former communications made to the Royal Society by the author. In the first of these (communicated in 1855), the deflection of the plumb-line caused by the mountain-mass north of Hindostan is calculated; and in the second (communicated in 1858), the effect of a small excess or defect of density ...
openaire +1 more source
Advanced Engineering Materials, EarlyView.Deep‐UV (258 nm) femtosecond pulses enable uniform amorphous silicon writing on Si(100)/(111) with a six‐fold larger fluence amorphization window than NIR methods. Optimized fluence and overlap yield 20–45 nm uniform and continuous amorphous layers. Microscopy shows sharp interfaces, and real‐time reflectivity reveals nanosecond melt–resolidification ...
Wissal Benali +5 more
wiley +1 more source
, 1974 plumb....you strike your centre line first generally, an' then you come (out here) * now an' now you'd plumb that down from the end o' the stake. You'd have a ...
core
Journal of Rehabilitation, 2006 Objective: Sway Back posture is one of the most common postural deformity.This study aimed to define Sway back posture prevalence and quantitatively meassure of the joints alignment in it.
Leila Simorgh +2 more
doaj
Advanced Engineering Materials, EarlyView.Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees +6 more
wiley +1 more source
Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials
Advanced Engineering Materials, EarlyView.Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley +1 more source
Letter from Senator Preston B. Plumb of Kansas to A. M. Claflin, 1888 July 31
, 1888 A letter from Senator Preston B. Plumb of Kansas to A. M. Claflin, President of the Chicago, St.
Plumb, Preston B.--1837-1891
core +1 more source
Self‐Cleaning Sensor Surfaces for Long‐Term Environmental Monitoring
Advanced Engineering Materials, EarlyView.Long‐term use of unattended outdoor sensors without soiling or biofouling is achieved through generation of a micro‐ and nanorough cuvette surface by combing hydrophobic nanoparticles with fluorinated polymers, crosslinked and surface‐attached through CHic chemistry. The coating demonstrates self‐cleaning behavior and prolonged outdoor stability, which
Sanam Kumari Rajak +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Gallium microalloying redirects interfacial reactions in low‐temperature Bi–Sn solders from Cu–Sn toward Cu–Ga intermetallic formation. The resulting Cu–Ga layer suppresses intermetallic growth during thermal aging, alters fracture pathways, and improves interfacial stability.
Iva Králová +6 more
wiley +1 more source
Morphology, Transport, and Dynamics of Protein Adsorption in Open‐Cell Metal Foam
Advanced Engineering Materials, EarlyView.Stainless steel (SS) open‐cell foams are shown to adsorb more protein per unit area than previously reported 316L SS and chromium oxide surfaces under static and flow conditions. An integrated approach combining 3D pore imaging, flow simulation, and protein adsorption experiments characterizes the foam’s performance.
Chinmaya Prerana Inguva +2 more
wiley +1 more source