Results 151 to 160 of about 7,885 (172)

Cutting Force and Processing Parameters Optimization of Plunge Milling for Die Steel

Advanced Materials Research, 2011
Plunge milling is used to remove excessive material rapidly in roughing machining. The cutter feed in the direction of machine spindle which has the highest structural rigidity. Through the single factor experiment of plunge milling a P20 die steel, this paper investigates the influence of side step, forward step, cutting speed, feed per tooth on ...
Y.M. Zhou, Cheng Yong Wang, Q.Y. Yang, Y.X. Song   +3 more
openaire   +1 more source

Evaluation of the Cutting Force and Geometric Error for Roughing Operation by Plunge Milling

Advanced Materials Research, 2011
Nowadays there has been noticeable an expressive technological development in the cutting process to machine moulds and dies, through applying new materials, cutting tools and machining strategies. The rough operations depict an important portion in the machining time of these pieces. In front of this scenario, a new milling rough operation in the tool’
Ivandro Bonetti, Valter Vander Oliveira, Adriano Fagali Souza   +2 more
openaire   +1 more source

Three-Dimensional Finite Element Analysis in Plunge Milling for Stainless Steel

Materials Science Forum, 2014
The three-dimensional finite element modeling and experimental validation of plunge milling of stainless steel (1Cr13) are presented. The commercial software Deform 3D applied for the finite element modeling is studied the effect of feed rate per tooth (fz) on the cutting forces and the temperature fields.
Yuan Sheng Zhai, Yu Wang, Fu Gang Yan, Bo Wang   +3 more
openaire   +1 more source

Research on Distributing of Cutting Temperature Field in Plunge Milling Ti Alloy

Volume 4: Design and Manufacturing, 2009
Theory model of cutting area temperature field is established based on superposition method of thermal source. Finite element simulation analysis of the cutting area temperature field of the workpiece is gotten by the method of the given heat source.
Xuda Qin, Xiaolai Ji, Weicheng Liu, Song Hua   +3 more
openaire   +1 more source

Trochoidal milling and plunging strategies in rough pocket milling of aluminium alloys

2006
Pocket milling is an essential issue in rough milling. Although the technology progress increased the machining capacities and enabled new machine structures, no significant evolution was observed about pocket milling trajectories. Trochoïds and plunge milling are new types of strategies which have found practical applications in hard materials rough ...
Hascoet, Jean-Yves, Rauch, Matthieu
openaire   +1 more source

Optimizing plunge milling aeronautical parts via MINLP

2015
no ...
Cafieri, S., Monies, Frederic, Mongeau, M., Bes, Christian   +3 more
openaire   +1 more source

Tool design and cutting parameters optimisation for plunge milling blisk

International Journal of Manufacturing Research, 2020
Yaonan Cheng, Jinlong Yang, Diange Zuo, Xu Song, Xinmin Feng   +4 more
openaire   +1 more source

Influential Parameters in Plunge Milling for Titanium Alloy Ti-6Al-4V

2019
Plunge milling is an interesting production mean for machining deep workpieces. It is identified as a process potentially able to afford significant gains in productivity during the roughing phases, especially in the case of workpieces made of hard materials.
Fredj, Montassar Abdelhack, Monies, F., Rubio, W., Senatore, J.   +3 more
openaire   +1 more source

A supplementary processing method of residual material in impeller plunge milling

Journal of Manufacturing Processes, 2023
X.Q. Wang, Z.C. Wei, D. Wang, D.B. Zhang, X.Y. Wang, M.J. Wang   +5 more
openaire   +1 more source

A study of interferential tool position correcting algorithms in 3D impeller variable-axis rough plunge milling

Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 2023
Lei Dong
exaly