Results 161 to 170 of about 457,914 (247)

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Multi-Scale Performance Assessment of Asphalt Mixtures Modified with Waste PVC Foils of Varying Geometries. [PDF]

Polymers (Basel)
Kırbaş U, İskender E, Kütük-Sert T, Hayat F, Kütük S.   +4 more
europepmc   +1 more source

A Compact Spin‐Coated Graphene UWB Antenna for Breast Tumor Detection

Advanced Engineering Materials, EarlyView.
A compact, spin‐coated graphene ultra‐wideband patch antenna designed for breast tumor detection, capable of distinguishing between malignant and benign tumors. This innovative antenna can serve as an effective initial screening tool, particularly in resource‐limited settings such as rural areas, where access to advanced medical equipment like MRI and ...
Raja Rashidul Hasan, Shuvra Saha, Sumit Hassan Eshan, Rinku Basak, Md. Nahian Al Subri Ivan, Ahmed Murtuza Saleque, Raja Tariqul Hasan Tusher, Sadia Zabin, Md. Abdur Rahman, Yuen Hong Tsang   +9 more
wiley   +1 more source

Study on coal wall spalling mechanism of large mining height working face based on folding mutation theory. [PDF]

Sci Rep
Li G, Zhang H, Li M, Shen Z, Tian A, Wang L.   +5 more
europepmc   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Enhancing flexural behavior and ductility of fixed-end RC beams using high-performance fiber-reinforced cementitious composites. [PDF]

Sci Rep
Sharbatdar MK, Ghods A, Sennah K.
europepmc   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

Adding blood flow restriction to isokinetic resistance training provides no additional benefit for strength, but may improve local muscular endurance: a randomized controlled trial. [PDF]

BMC Sports Sci Med Rehabil
Günaydın H, Akınoğlu B, Örsçelik A, Asar E, Büyüklüoğlu G, Kocahan T.   +5 more
europepmc   +1 more source

A Numerical–Experimental Approach for Multi‐Matrix Fiber‐Reinforced Plastics Characterization Using Finite Element Model Updating

Advanced Engineering Materials, EarlyView.
A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora, Tales V. Lisbôa, Axel Spickenheuer, Rogério J. Marczak, Jakson M. Vassoler   +4 more
wiley   +1 more source

Optimal Design of CFRP Railway Carbody Laminates via Multi-Criterion Fiber Orientation Sensitivity. [PDF]

Materials (Basel)
Cascino A, Meli E, Rindi A.
europepmc   +1 more source