Results 101 to 110 of about 89,512 (318)
Irregular, Adaptive Scan Trajectories for Pulsed Laser Micro Polishing
, 2013 The objective of this work is to generate irregular, smooth, adaptive laser scan trajectories for pulsed laser micro polishing (PL?P). Traditionally PL?P, like other surface finishing processes has used zigzag scan paths.
Li, Xiaochun +4 more
core
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Influência das condiçoes mecânicas e físico-químicas no processo de brunimento plano rotativo de placas de porcelanato [PDF]
, 2012 Dissertação (mestrado) - Universidade Federal de Santa Catarina, Centro Tecnológico, Programa de Pós-Graduação em Ciência e Engenharia dos Materiais, Florianópolis, 2012.Apesar dos avanços tecnológicos e mercadológicos nos processos produtivos de placas ...
Pereira, Rafael Santiago Floriani
core
Immediate versus water-storage performance of Class V flowable composite restoratives
, 2006 Objectives The aims of this investigation were to clarify the effects of 24 h water-storage and finishing time on mechanical properties and marginal adaptation to a Class V cavity of eight modern flowable resin-composites.
Hatanaka, Kenji +4 more
core +1 more source
Advanced Engineering Materials, EarlyView.This study explored how effective nickel aluminide coatings are obtained in providing oxidation resistance applied to the Inconel 738 alloy, modeling with diffusion models. In the present study, kinetics and thermal behavior of the Inconel 738 alloy were studied by the low‐temperature thermoreactive aluminizing process, which was carried out at 625°C ...
Gozde Celebi Efe +4 more
wiley +1 more source
Experimentation to Reduce Friction from Novel Abrasive Tape Polishing Method
, 2010 The aim is to develop and improve a finishing process that allows reduced CO2 emissions, through reduced use of carbon-based fuels, achieving improvement in fuel consumption.
Chen, Xun, Blunt, Liam, Wilkinson, Adam
core
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Study on Precision Polishing of a Long Fine Cylinder
, 2014 This research aimed to design and develop a polishing system for precision polishing cylindrical specimen to nanometer surface finish. An experimental polishing system was built in the present study to polish nickel plated specimens with various ...
Chao, Choung-Lii; Chou, Wen-Chen; Kuo, Chia-Wei; Lai, Alan W.; Lin, Hung-Yi
core
A method for extracting travel patterns using data polishing [PDF]
With recent developments in ICT, the interest in using large amounts of accumulated data for traffic policy planning has increased significantly. In recent years, data polishing has been proposed as a new method of big data analysis.
桑野, 将司 +15 more
core +1 more source
A Workflow to Accelerate Microstructure‐Sensitive Fatigue Life Predictions
Advanced Engineering Materials, EarlyView.This study introduces a workflow to accelerate predictions of microstructure‐sensitive fatigue life. Results from frameworks with varying levels of simplification are benchmarked against published reference results. The analysis reveals a trade‐off between accuracy and model complexity, offering researchers a practical guide for selecting the optimal ...
Luca Loiodice +2 more
wiley +1 more source