Results 51 to 60 of about 544,223 (173)
ROBOMECH Journal, 2021 In this study, we evaluated the deformation shape of a balloon-type dielectric elastomer actuator (DEA) that has been prestretched with water pressure. We fabricated the DEA with poly(dimethylsiloxane) (PDMS) as the elastomeric material and carbon grease
Natsumi Koike, Takeshi Hayakawa
doaj +1 more source
A Monolithic Janus Hydrogel Pressure Sensor for Wearable Motion and Physiological Monitoring
Advanced Science, EarlyView.This work reports a monolithic Janus hydrogel pressure sensor featuring integrated conductive PEDOT and insulating PEGDA layers. The fabricated device achieves a rapid response time, a wide operating range, and good cyclic durability. The sensor demonstrates robust performance in tracking dynamic human joint motions, offering a scalable strategy for ...
Syed Atif Ali +7 more
wiley +1 more source
Nanotribology of Poly(dimethylsiloxane) Melt Confined between Hydrophobic Surfaces
Tribology Online, 2006 Friction measurements were carried out for a poly(dimethylsiloxane) (PDMS) melt (Mw ≈ 80000) confined between hydrophobic surfaces using the surface forces apparatus.
Shinji Yamada
doaj +1 more source
Unipolar Barrier Near‐Infrared 2D Photodetectors for 3D Image Sensors
Advanced Science, EarlyView.A MoTe2/WSe2/Cl–SnSe2 unipolar barrier photodetector is demonstrated, in which the WSe2 layer effectively blocks majority‐carrier injection, yielding suppressed dark current and enhanced near‐infrared (NIR) sensing. The device achieves high detectivity, a wide linear dynamic range, and fast response under 1310 nm illumination, enabling high‐fidelity 3D
Jung Pyo Hong +21 more
wiley +1 more source
, 2010 A novel and simple method for the rapid fabrication of microfluidic networks is presented. A silicone elastomer (PDMS - poly(dimethylsiloxane)) is cured around formers, which are then removed post-cure, resulting in a microstructure suitable for fluidic ...
Lewis, Adam +7 more
core +1 more source
Advanced Science, EarlyView.Butterfly wing–inspired intrinsically self‐healing polymer interlayers enable flexible perovskite optoelectronics with high luminance, strain‐insensitive stability, and environmental resilience. These hierarchically structured films redistribute mechanical stress, suppress defect formation, and maintain performance under repeated bending, paving the ...
Loganathan Veeramuthu +13 more
wiley +1 more source
THERMOGRAVIMETRIC STUDIES OF POLY(OXYMETHYLENE-CO-DIMETHYLSILOXANE) COPOLYMERS
, 1993 The thermal stability and kinetic parameters of a series of poly(oxymethylene-co-dimethylsiloxane) copolymers have been studied by thermogravimetry from 303 to 846K under nitrogen flow. The new copolymers, obtained by ring-opening copolymerization of 1,3,
ZAPATA, M +3 more
core +1 more source
Bottom-Up Fabrication of PEG Brush on Poly(dimethylsiloxane) for Antifouling Surface Construction
International Journal of Polymer Science, 2016 Poly(dimethylsiloxane) silicones have found many applications in biomedical devices, whereas their surface hydrophobicity always brings about unexpected bioadhesion, causing complications of the implanted biomedical devices.
Junmei Tang +3 more
doaj +1 more source
Advanced Electronic Materials, EarlyView.Composite‐based flexible electronics integrate biodegradable polymers, conductive networks, and multilayer device architectures to balance electrical performance, mechanical durability, and controlled degradation. Interfacial engineering and encapsulation regulate transport stability and operational lifetime, while programmed disassembly enables ...
Sayam, Sangho Cho
wiley +1 more source
Direct Poly(dimethylsiloxane) Surface Functionalization with Vinyl Modified DNA
, 2016 Direct Poly(dimethylsiloxane) Surface Functionalization with Vinyl Modified ...
Kevin A. Heyries (567568) +2 more
core +1 more source