Results 41 to 50 of about 25,486 (191)
Properties of kenaf fiber-reinforced polyamide 6 composites
e-PolymersDespite the increasing interest in polyamide-based composites, few studies on polyamide-based natural fiber composites have been conducted due to their high melting temperatures of polyamide 6 (PA6).
Abdullah Norihan +5 more
doaj +1 more source
Evaluation of impact strength of polyamide 6/bentonite clay nanocomposites
Materials Research, 2012 Nanocomposites of polymer/clay have had much attention in recent years, particularly those developed with layered silicates due to the need of engineering materials more efficient than pure polymers for certain applications.
Rene Anisio Paz +5 more
doaj
The Feasibility of an Internal Gas-Assisted Heating Method for Improving the Melt Filling Ability of Polyamide 6 Thermoplastic Composites in a Thin Wall Injection Molding Process [PDF]
, 2021 Thanh Trung +2 more
openalex +1 more source
Polyamide 6/Layered Silicate Nanocomposites
Acta Physica Polonica A, 2008 Polyamide 6 (PA6) and its two exfoliated nanocomposites (PA6/Nf919 and PA6/BZ-COCO), with bentonite (2.5 wt.%) organophilically treated with difierent cations, were studied. Improved mechanical properties, changes in crystallinity and morphology as well as higher glass transition temperature values were observed for the nanocomposites in comparison to ...
M. Dębowska +3 more
openaire +1 more source
Development of polyamide-6/chitosan membranes for desalination
Egyptian Journal of Petroleum, 2014 This article deals with “developing novel polyamide-6/chitosan membranes for water desalting using wet phase inversion technique”, in which novel polyamide-6/chitosan membranes were prepared using an appropriate polymer concerning the national ...
A. EL-Gendi +3 more
doaj +1 more source
Polímeros, 2007 Este trabalho avalia a utilização da cinza da casca de arroz como carga estrutural em poliamida 6 e poliamida 6.6. Estas matrizes poliméricas são importantes plásticos de engenharia com aplicações em várias áreas.
Waldir P. Ferro +2 more
doaj +1 more source
Constant Temperature Approach for the Assessment of Injection Molding Parameter Influence on the Fatigue Behavior of Short Glass Fiber Reinforced Polyamide 6 [PDF]
, 2021 Selim Mrzljak +6 more
openalex +1 more source
Nanofibrous polyamide 6 scaffolds promote adhesion of endothelial cells
Current Directions in Biomedical Engineering, 2018 The usage of synthetic scaffolds is a promising approach in development of implant materials. In this study we fabricated nanofibrous nonwovens of polyamide 6 (PA-6) by means of electrospinning and performed a systematic characterization with regard to ...
Khaimov Valeria +4 more
doaj +1 more source
Characterization of polyamide-6/ propolis blended electrospun fibers
Heliyon, 2020 Polyamide-6 (PA-6) nanofibers and PA-6/propolis ethanolic extract (EEP) blended fibers were prepared having electrospun their solutions in formic acid as solvent.
Bibi Marzieh Razavizadeh +1 more
doaj +1 more source
Scientific Reports, 2021 The method of pre-irradiation grafting was used with the aid of electron beam (EB) accelerator to accomplish the grafting of polyamide 6 fibers (PA6) with glycidyl methacrylate (GMA).
Shihab Ezzuldin M.Saber +4 more
doaj +1 more source