Results 151 to 160 of about 23,852 (216)

Construction of a P/N/Zn Synergist for Enhancing the Fire Safety and Char Formation of PA6/Aluminum Diethylphosphinate Composites. [PDF]

Polymers (Basel)
Peng Q, Hua Y, Yang J, Wang Y, Guo G, Li W, Sun J, Gu X, Li J, Zhang S.   +9 more
europepmc   +1 more source

Polyethylene‐Polyamide‐6 Diblock Copolymers for Fused Filament Fabrication

Journal of Polymer Science, EarlyView.
Linear HDPE‐PA6 block copolymers were prepared by polymerization of ethylene to a macroinitiator and subsequent anionic caprolactam polymerization. The copolymer with a HDPE mass of 6500 Da and PA6 mass of 20.000 Da was used as a filament in 3D printing.
Elsa M. Schoeneberger, Gerrit A. Luinstra   +1 more
wiley   +1 more source

Doctor-blading-assisted interfacial polymerization for green and scalable polyamide membrane fabrication. [PDF]

Nat Commun
Zhao G, Liu H, Lan C, Liang L, Dong L, Meng H, Elimelech M.   +6 more
europepmc   +1 more source

Evaluation of a High‐Performance Monopropellant Formed of Microencapsulated Hydrocarbon Fuels in Combination With Gelled Hydrogen Peroxide in a Strand Burner Setup

Propellants, Explosives, Pyrotechnics, EarlyView.
A high‐performance premixed monopropellant is prepared from hydrocarbon‐filled microcapsules and hydrogen peroxide. This propellant is burned in a strand burner, and the effect of different parameters on the burn rate is evaluated. ABSTRACT A dispersion of hydrocarbon‐fuel‐filled microcapsules in gelled hydrogen peroxide can form a premixed ...
Robin Scholl, Felicitas S. Moll, Dominic Freudenmann, Stefan Schlechtriem   +3 more
wiley   +1 more source

Feasibility Study of Suitable Surface Treatments for 3D-Printed Parts to Increase Abrasion Resistance Stability. [PDF]

Polymers (Basel)
Fink D, Chval Z, Raz K.
europepmc   +1 more source

Conductive Hydrogel‐Enabled Electrode for Scalp Electroencephalography Monitoring

Small Methods, EarlyView.
Conductive hydrogels are emerging as effective EEG electrode‐scalp interfaces to overcome hair barriers. This review presents the demanding parameters for hair‐compatible hydrogel electrodes and summarizes their applications in healthcare and brain‐computer interfaces.
Zichong Ji, Leqi Li, Meiqiong Zheng, Xinyuan Ye, Wenqing Yan, Zonglei Wang, Yi Liu, Yuli Wang, Yujie Zhang, Pengcheng Zhou, Jiawei Yang, Mingzhe Wang, Shihong Lin, Hossam Haick, Yan Wang   +14 more
wiley   +1 more source

Influence of Viscous Dissipation on Wear Behavior and Hardness Evolution of Tool Steels in Glass‐Fiber‐Reinforced Polymer Processing

steel research international, EarlyView.
Tool steels tested under injection molding conditions with glass‐fiber‐reinforced polymers, revealing how viscous dissipation drives hardness loss, even in PM grades. A sharp rise in wear with increasing injection volume rate and thermomechanical load uncovers striking material differences.
David Zidar, Roman Staudigl, Walter Friesenbichler, Clemens Holzer   +3 more
wiley   +1 more source

Chest wall stabilization following hemi-sternectomy assisted by 3D printed model. [PDF]

Case Reports Plast Surg Hand Surg
Nichols PL, Brown CW, Wenger DC, Osher JM, Powers JM.   +4 more
europepmc   +1 more source

Recent Advances and Perspectives in UL‐94 V‐0 Rated Flame‐Retardant Polycarbonate: Addressing Challenges Under Per‐ and Polyfluoroalkyl Substances Bans

Safety Science and Technology, EarlyView.
Based on the challenges and motivations of global PFAS bans, this review highlights recent advances in strategies achieving UL‐94 V‐0 flame retardancy in polycarbonate while maintaining critical comprehensive performances, offering perspectives for future R&D. ABSTRACT This review focuses on the recent advancements in the development of UL‐94 V‐0 rated
Ting Sai, Xiaodi Ye, Bingtao Wang, Juan Li, Xin Zhang, Zhenghong Guo, Siqi Huo, Pingan Song, Zhengping Fang   +8 more
wiley   +1 more source