Results 191 to 200 of about 97,061 (304)

Behavior of a Novel Cyclic Olefin‐Based Hot‐Melt Adhesive in CFRP Adhesive Joints Compared to Conventional Epoxy‐Based Structural Adhesives

Polymer Composites, EarlyView.
Rate‐dependent performance of composite adhesive joints using thermoset and thermoplastic adhesives, in terms of toughness and fatigue behaviour. ABSTRACT A recently developed hot‐melt adhesive (HMA) based on cyclic olefin chemistry, supplied as a transparent, non‐tacky thermoplastic film with a distinctive polymer microstructure, was evaluated in this
Hossein Malekinejad, Ricardo J. C. Carbas, Eduardo A. S. Marques, Lucas F. M. da Silva   +3 more
wiley   +1 more source

Optimization of an analytical methodology to determine microplastic contamination in different seaweed groups (Phaeophyceae, Rhodophyta and Chlorophyta). [PDF]

MethodsX
Pereira R, Almeida CMR, Ramos S.
europepmc   +1 more source

Effects of Cooling Rates on Self‐Reinforced Polyethylene Composites via Multiscale Experimental Characterizations

Polymer Composites, EarlyView.
(top) fabrication and multi‐scale characterizations of self‐reinforced polyethylene composites (PE‐SRCs); (bottom) effects of cooling rates on mechanical properties and crystal morphologies of PE‐SRCs. ABSTRACT This study investigates cooling rate effects on self‐reinforced polyethylene composites (PE‐SRCs), focusing on macroscopic thermal and ...
Yelin Ni, Yao Qiao, Logan Kearney, Raveen John, Dounia Boushab, Ethan Nickerson, Amit Naskar, Kevin Simmons   +7 more
wiley   +1 more source

Improvement of islet transplantation in prevascularized muscle sinus tracts. [PDF]

iScience
Jin M, Liu L, Fu J, Jiang Z, Ma X, Gao Z, Liu X, Zhou B, Li G, Zhang Y, Fu H, Yan S.   +11 more
europepmc   +1 more source

Rheology–Performance Framework for PA6/GO Nanocomposites via a Hybrid Processing Route

Polymer Engineering &Science, EarlyView.
Hybrid PA6/GO nanocomposites with tuned melt rheology and improved thermal–mechanical performance. ABSTRACT Balancing melt processability with stiffness and heat resistance remains a central challenge for PA6 nanocomposites. Here, graphene oxide (GO) was synthesized by a modified Hummers method and incorporated into PA6 via a hybrid route (solution ...
Caio César Nogueira de Melo, Chiara Dores do das Nascimento, Everton Granemann Souza, André Lamounier Caixeta, Cesar Augusto Gonçalves Beatrice, Luiz Antonio Pessan, Amanda Dantas de Oliveira, Fernando Machado Machado   +7 more
wiley   +1 more source

Nanoimprinted polyamide membranes for ultrafast and precise molecular sieving with low fouling. [PDF]

Nat Commun
Jin P, Yang Z, Ceyssens F, Yang J, Yuan S, Wang H.   +5 more
europepmc   +1 more source

Enhancing the Properties of PA6 and PA6/Ionomer Scraps Blend With CaCO3 Nanoparticles: Rheological, Mechanical, Thermal, and Morphological Evaluation

Polymer Engineering &Science, EarlyView.
ABSTRACT This study investigated the effects of incorporating ionomer scraps and CaCO3 nanoparticles on the rheological, mechanical, thermal, and morphological properties of neat polyamide 6 (PA6) and a PA6/ionomer scraps (80/20) blend. The ionomer formed an immiscible dispersed phase within the PA6, acting as an impact modifier; however, it reduced ...
Roberto Alves Taveira Jr., Patrícia Schmid Calvão, Adriana Martinelli Catelli Souza   +2 more
wiley   +1 more source

Fabrication of Polyamide Thin-Film Composite/Polyethersulfone-Coreshell-Fe₃O₄/ZnO Membranes for the Efficient Removal of Pb(II) from Wastewater. [PDF]

Membranes (Basel)
Kubheka NSM, Managa M, Moloto MJ, Nxumalo EN.   +3 more
europepmc   +1 more source

Enhancing the Tribological Performance of PLA via Process‐Induced Functional Grading in Masked Stereolithography

Polymer Engineering &Science, EarlyView.
An exposure‐time‐controlled MSLA fabrication strategy enabling filler‐free functionally graded polymers, resulting in up to a 62% reduction in specific wear rate. ABSTRACT Masked stereolithography (MSLA) enables high‐resolution fabrication of photopolymer components; however, the limited tribological performance of neat resins restricts their ...
Muhammet Mevlüt Karaca, Abdurrahim Temiz, Fatih Huzeyfe Öztürk   +2 more
wiley   +1 more source

Feasibility Study of Suitable Surface Treatments for 3D-Printed Parts to Increase Abrasion Resistance Stability. [PDF]

Polymers (Basel)
Fink D, Chval Z, Raz K.
europepmc   +1 more source