Results 201 to 210 of about 65,206 (305)

Three-Dimensional Printed Polyamide 12 (PA12) and Polylactic Acid (PLA) Alumina (Al₂O₃) Nanocomposites with Significantly Enhanced Tensile, Flexural, and Impact Properties. [PDF]

Nanomaterials (Basel), 2022
Petousis M, Vidakis N, Mountakis N, Papadakis V, Tzounis L.   +4 more
europepmc   +1 more source

Carbon/polyamide 12 prepreg production [Karbon/poliamid 12 film kompozit üretimi]

, 2019
Lightweightness and strength of carbon fibers also give importance to prepregs produced using them. Prepregs are semi-finished products preferred especially for their advantages such as the control of fiber volume fraction and the easiness in the production of laminated composites.
Yildiz H., Erden S.
openaire   +1 more source

Enhancing the Properties of PA6 and PA6/Ionomer Scraps Blend With CaCO3 Nanoparticles: Rheological, Mechanical, Thermal, and Morphological Evaluation

Polymer Engineering &Science, EarlyView.
ABSTRACT This study investigated the effects of incorporating ionomer scraps and CaCO3 nanoparticles on the rheological, mechanical, thermal, and morphological properties of neat polyamide 6 (PA6) and a PA6/ionomer scraps (80/20) blend. The ionomer formed an immiscible dispersed phase within the PA6, acting as an impact modifier; however, it reduced ...
Roberto Alves Taveira Jr., Patrícia Schmid Calvão, Adriana Martinelli Catelli Souza   +2 more
wiley   +1 more source

An experimental and theoretical investigation on the hyper-viscoelasticity of polyamide 12 produced by selective laser sintering. [PDF]

PLoS One
Kadkhodaei M, Pawlikowski M, Drobnicki R, Domański J.   +3 more
europepmc   +1 more source

Tribological Behavior of 3D-Printed Nanometer SiC and SiO₂ Particle-Reinforced Polyamide 12 Composites by Selective Laser Sintering under Seawater Lubrication Condition. [PDF]

Polymers (Basel), 2022
Ma J, Yu G, Wang X, Li J, Wu J, Wang X.
europepmc   +1 more source

Enhancing the Tribological Performance of PLA via Process‐Induced Functional Grading in Masked Stereolithography

Polymer Engineering &Science, EarlyView.
An exposure‐time‐controlled MSLA fabrication strategy enabling filler‐free functionally graded polymers, resulting in up to a 62% reduction in specific wear rate. ABSTRACT Masked stereolithography (MSLA) enables high‐resolution fabrication of photopolymer components; however, the limited tribological performance of neat resins restricts their ...
Muhammet Mevlüt Karaca, Abdurrahim Temiz, Fatih Huzeyfe Öztürk   +2 more
wiley   +1 more source

Optimization of Mechanical Properties and Evaluation of Fatigue Behavior of Selective Laser Sintered Polyamide-12 Components. [PDF]

Polymers (Basel)
Sommer D, Stockfleet H, Hellmann R.
europepmc   +1 more source

Temperature-dependent tensile properties of polyamide 12 for the use in percutaneous transluminal coronary angioplasty balloon catheters. [PDF]

Biomed Eng Online, 2021
Amstutz C, Weisse B, Valet S, Haeberlin A, Burger J, Zurbuchen A.   +5 more
europepmc   +1 more source

Influence of Build Orientation and Part Thickness on Tensile Properties of Polyamide 12 Parts Manufactured by Selective Laser Sintering. [PDF]

Polymers (Basel)
Slager JJ, Earp BC, Ibrahim AM.
europepmc   +1 more source

Characteristics, properties and limitations of per‐ or polyfluoroalkyl substances (PFASs) and fluoropolymers

Polymer International, EarlyView.
An overview and categorization of man‐made per‐ or polyfluoroalkyl substances (PFASs) including low‐molar‐mass and high‐molar‐mass fluorochemicals, and their international regulations is presented. Though certain PFASs are toxic, bioaccumulative and cross the human cellular membranes, others, such as fluoropolymers, are safe, reliable and involved in ...
Bruno Améduri
wiley   +1 more source