Results 11 to 20 of about 27,543,308 (166)
Interlocking shish‐kebab morphology in polybutene‐1 [PDF]
Journal of Polymer Science Part B: Polymer Physics, 2002 AbstractThe aim of this research was to explore the effect of shear‐controlled orientation injection molding (SCORIM) on polybutene‐1 (PB‐1). This article describes the methods and processing conditions used for injection molding and discusses the properties of the moldings.
Kalay G., Kalay, C.R.
openaire +5 more sources
Microstructure and Tensile Properties of Melt-Spun Filaments of Polybutene-1 and Butene-1/Ethylene Copolymer. [PDF]
Polymers (Basel), 2023 Polybutene-1 with form I crystals exhibits excellent creep resistance and environmental stress crack resistance. The filaments of polybutene-1 and its random copolymer with 4 mol% ethylene co-units were produced via extrusion melt spinning, which are ...
Li J +11 more
europepmc +2 more sources
The influence of branching efficiency on the rheology and morphology of melt state long chain branched polypropylene/polybutene-1 blends [PDF]
Polyolefins Journal, 2019 In this study, the compatibility of the blends of polypropylene (PP) and polybutene-1(PB-1) homopolymer before and after long chain branching process were studied.
Ali Foroozan +2 more
doaj +1 more source
Polymer Testing, 2023 Isotactic polybutene-1 (PB)/isotactic polypropylene (PP) blends, typical crystalline/crystalline polymer blends with low-melting-temperature (Tm) PB and high-Tm PP, exhibit complicated interactions between their components in both molten and solid states.
Xiangjie Yan +5 more
doaj +1 more source
Polymer Testing, 2023 The creep resistance of polymer determines the dimensional stability of product under stress. The isotactic polybutene-1 (iPB) with outstanding high-temperature creep resistance and stress-crack resistance is applied widely in the field of hot-water ...
Yuanjin Zhao +3 more
doaj +1 more source
Journal of CO2 Utilization, 2023 As a polycrystalline polymer, isotactic polybutene-1 (iPB-1) will form different crystalline structures when it crystallizes under different conditions. In this work, we found a simple method to manipulate the cell structure of iPB-1 foams by controlling
Weijie Li +4 more
doaj +1 more source
Crystallinity and Stereoregularity of Polybutene-1
Kobunshi Kagaku, 1962 X線回折による結晶化度と密度とを主としてZieglem触媒により合成したポリブテン-1について測定した。結晶化度と比容積との間に直線関係が成立することから, 結晶質と非晶質の密度の値0.950および0, 868が得られた。アイソタクチックポリブテン-1には結晶化バンドとみなしうる吸収が多数見出された。一方, 1221cm-1バンドは固態状態ではその吸光度比の値が比容積と直線関係を示すが溶融状態や溶液で消失しない。したがって固態状態で一定の熱処理をした試料について比較するときには結晶化度の尺度として使用しうると考えられる。吸光度比 (A1221/A1151) と密度 (d) との間には次の実験式が成立する。
Atsuo Nishioka, Kazuo Yanagisawa
+6 more sources
Interfacial structure and properties of isotactic polybutene-1/polyethylene blends
e-Polymers, 2022 Polymer blending is one of the most economical and effective techniques for achieving products with high comprehensive performances. However, the immiscibility between polymers results in a weak interface, which is typically the position where material ...
Niu Xiu +5 more
doaj +1 more source
Polymer Testing, 2023 Investigating the structure of spherulite is instructive for better understanding the polymer crystallization process and mechanism, which is critical for the design and manufacture of polymeric products with high performance. Wide angle X-ray scattering
Peng Rao +5 more
doaj +1 more source
Fracture and Structural Integrity, 2013 Isotactic polybutene-1 (i-PB1) is a polymer used for the manufacturing of pressurized pipes. In this work two grades of i-PB1 with a different degree of isotacticity have been investigated; they have been supplied by Basell Polyolefins. Fracture tests
Luca Andena +2 more
doaj +3 more sources