Results 61 to 70 of about 5,625 (250)

Effect of Superplasticizer Concentration on Cement Hydration at Low Water to Cement Ratios: Electrochemical Impedance Spectroscopy Study

open access: yesInternational Journal of Electrochemical Science, 2019
The hydration behavior and the fluidity of cementitious mortar samples with water to cement ration of less than 0.2 were studied. Polycarboxylate ether (PCE) superplasticizers in different dosages were used to investigate the hydration process of fresh ...
Xiong-zhou Yuan   +3 more
doaj   +1 more source

Effect of Superplasticizer and Wetting Agent on Volumetric and Mechanical Properties of Cold Recycled Mixture with Asphalt Emulsion

open access: yesAdvances in Materials Science and Engineering, 2020
Cold recycled mixture with asphalt emulsion (CRME) has gained more appreciation due to its environmental and economical advantages. Surfactant greatly affects the interaction between asphalt emulsion and cement, which can greatly affect the volumetric ...
Wenting Yang   +5 more
doaj   +1 more source

Rheological and hydration characterization of calcium sulfoaluminate cement pastes [PDF]

open access: yes, 2015
Calcium sulfoaluminate (CSA) cements are currently receiving a lot of attention because their manufacture produces less CO2 than ordinary Portland cement (OPC).
García-Aranda, Miguel Ángel   +4 more
core   +1 more source

Concrete breakout strength prediction of anchors in Steel Fiber Reinforced Concrete based on material test datasets

open access: yesStructural Concrete, EarlyView.
Abstract The use of steel fiber‐reinforced concrete (SFRC) has seen a significant rise in the construction industry due to advancements in material science, improved quality, and cost efficiency. Similarly, the importance of fastening systems in construction has grown, necessitating robust research on the performance of fasteners in SFRC to ensure safe
Nikolaos Mellios, Panagiotis Spyridis
wiley   +1 more source

Evaluation of Rheological Parameters of Slag-Based Paste Backfill with Superplasticizer

open access: yesAdvances in Materials Science and Engineering, 2021
The use of blast furnace slag-based binders in cemented paste backfill (CPB) has become increasingly popular in China, due to its low cost and superior early-age strength. Increasing the solid content can increase the strength of CPB, but it will lead to
Zhonghui Zhang   +5 more
doaj   +1 more source

PENGARUH VARIASI JENIS DAN PERSENTASE SUPERPLASTICIZER TERHADAP TEMPERATUR HIDRASI DAN SUSUT BETON MUTU TINGGI [PDF]

open access: yes, 2014
Penelitian ini dilakukan untuk mengetahui pengaruh dari jenis dan persentasesuperplasticizer terhadap temperatur hidrasi dan penyusutan (shrinkage) beton mutu tinggi.Pengukuran temperatur hidrasi dilakukan dengan metode semi adiabatik kalorimeter ...
ZULFAHMI
core  

Clays for Low‐Carbon Cements: Overview, Progress, and Challenges

open access: yesGlobal Challenges, Volume 10, Issue 1, January 2026.
This review provides a critical overview of recent developments of activated clays to function as artificial pozzolans. After a thorough description of the clays that yield good pozzolanic performances, selected examples are given on thermal and mechanical activations. Chiefly, general correlations are extracted from reported data despite its scattered
Imane Koufany   +4 more
wiley   +1 more source

Impact of air entrainment on the microstructure and mechanical performance of high performance mortar [PDF]

open access: yes, 2014
At the Magnel Laboratory for Concrete Research an intensive vacuum mixer which can regulate the air pressure is available. As such the amount of entrapped air in cementitious materials can be varied.
Boel, Veerle   +2 more
core   +2 more sources

Investigation of the Incompatibilities of Cement and Superplasticizers and Their Influence on the Rheological Behavior [PDF]

open access: yes, 2020
The rheological behavior of cement paste and the improvement of its flowability takes center stage in many research projects. An improved flowability can be achieved by the addition of superplasticizers (SP), such as polycarboxylate ethers (PCE).
Jakob, Cordula   +4 more
core   +2 more sources

Development of EPS light‐weight concrete for 3D printing

open access: yesStructural Concrete, Volume 26, Issue 6, Page 7256-7268, December 2025.
Abstract This study investigates the feasibility of 3D printing lightweight concrete (LWC) incorporating expanded polystyrene (EPS) beads, with a focus on optimizing mechanical properties and flowability for 3D concrete printing (3DCP). The research addresses the need for printable, structurally viable lightweight materials by developing and testing ...
Nima Aminpour, Ali Memari
wiley   +1 more source

Home - About - Disclaimer - Privacy