Results 121 to 130 of about 1,020,253 (390)
Ultra thin gage plastic film [PDF]
, 1971 Process utilizing specially modified conventional equipment, with changes in process temperature, pressure, and cooling requirements produces ultra thin 1.56 micron /0.0614 mil/ thick polyethylene ...
Cox, D. W., Jr., Struble, A. D.
core +1 more source
Macromolecular Materials and Engineering, 2002 The main objective of this study is to investigate the barrier mechanisms and properties of polyethylene, polyethylene (PE)/polyamide (PA) and polyethylene/modified polyamide (MPA) bottles against paint solvent permeation. In addition to the paint mixed solvent, the barrier properties of these bottles against the permeation of pure main solvents ...
Wei-Hsiang Shih +2 more
openaire +1 more source
Creep in polyethylene and hydroxyapatite reinforced polyethylene composites
Journal of Materials Science: Materials in Medicine, 1995 Isochronous stress-strain relationships and long term creep performance for unfilled and hydroxyapatite filled polyethylene composites have been studied. The tests were carried out in a buffered (pH=7.5) Ringer's solution at 37°C. It was observed that the inclusion of hydroxyapatite does not remove the non-linear viscoelasticity of polyethylene.
Suwanprateeb +3 more
openaire +2 more sources
Time‐Controlled Dual Targeting to Program Systemic and Intercellular Transfer of Therapeutic Effects
Advanced Functional Materials, EarlyView.Aspirin‐liposomes loaded onto monocytes enable inflammation‐triggered targeting and efficient hand‐over of aspirin to inflamed cells. Monocytes uptake a significant portion of aspirin‐liposomes, prolonging therapeutic action. This approach enhances anti‐inflammatory effects through intercellular transfer, demonstrating a translational strategy for ...
Seung Eun Yu +6 more
wiley +1 more source
Low temperature thermal expansivities of polyethylene, polypropylene and their mixtures [PDF]
Low temperature measurements of length- temperature curves of polyethylene, polypropylene, mixtures of polyethylene and polypropylene, and ...
Simha, R., Zakin, J. L.
core +1 more source
Advanced Functional Materials, EarlyView.This research utilizes selective reduction laser sintering (SRLS) to engineer In2O3 NPs for flexible NO2 sensors. The introduction of oxygen vacancy defects enhances sensor performance, offering excellent responsiveness, rapid response/recovery, superior selectivity, low detection limit, and long‐term stability.
Shaogang Wang +8 more
wiley +1 more source
INFLUENCE OF XENOBIOTICS ON THE BIOLOGICAL SOIL ACTIVITY [PDF]
Journal of Central European Agriculture, 2002 The both basic and potential biological soil activity along with a biological degradation capacity of soil microorganisms through their respiratory activity were investigated after the application of polymers with the different degree of degradation in ...
S JAVOREKOVÁ +3 more
doaj
Influence of Adding Different Fillers on Polyethylene Properties
Tikrit Journal of Engineering Sciences, 2006 The aim of this study was focused on the improvement of pouring, mechanical and thermal properties of high density polyethylene using chemically treated kawaline as a filler which is composed of 10% carbamide and 90% kawaline.
Abdulla Abd Al-shakoor +2 more
doaj +1 more source
Environmental toxicity and decomposition of polyethylene.
Ecotoxicology and Environmental Safety, 2022 Zhu Yao, Hyeon Jeong Seong, Y. Jang
semanticscholar +1 more source
Wetting of Surface Grafted Hydrophilic‐b‐Hydrophobic Block Copolymer Brushes
Advanced Functional Materials, EarlyView.The wetting properties of surface grafted diblock copolymer brushes are influenced by the thickness of the hydrophilic bottom block and the hydrophobic top block. The surface adapts in presence of water and the contact angles of the bottom block shine through. Abstract The wetting of diblock copolymer brushes by water is studied.
Benjamin Leibauer +7 more
wiley +1 more source