Results 61 to 70 of about 751,378 (297)
A new gas discharge process for preparation of non-fouling surfaces on biomaterials [PDF]
, 1993 A non-fouling surface containing immobilized polyethylene oxide (PEO) was achieved using an argon radio-frequency glow discharge treatment (RFGD) of polyethylene films precoated with Brij hydrocarbon-PEO surfactants.
Feijen, J. +3 more
core +2 more sources
Evaluating Energy Absorption Performance of Filled Lattice Structures
Advanced Engineering Materials, EarlyView.Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney +2 more
wiley +1 more source
KAPASITAS LENTUR, TOUGHNESS, DAN STIFFNESS BALOK BETON BERSERAT POLYETHYLENE [PDF]
, 2006 The common problems of concrete are brittle failure and low of tension. Fiber reinforced plastic concrete is one of the alternatives to solve the problems. This research aim is to demonstrate a contribution of Polyethylene to revise the weakness of its
Wibowo,
core
Influence of thermal treatment and residues on space charge accumulation in XLPE for DC power cable application [PDF]
, 2007 Effects of cross-linking by-products (residues) of polyethylene on space charge accumulation and decay are investigated in the paper using the pulsed electro-acoustic technique.
Chen, G. +3 more
core +1 more source
Advanced Engineering Materials, EarlyView.This study reports lightweight polyetherimide triply periodic minimal surfaces lattices coated with carbon nanotube‐reinforced epoxy that combine mechanical robustness with self‐sensing. The conformal coating enhances stiffness, strength and energy absorption while enabling reliable strain monitoring.
A. Triay +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley +1 more source
Space Charge Characteristics and Electrical Properties of Micro-Nano ZnO/LDPE Composites
Crystals, 2019 The synergistic effects of zinc oxide (ZnO) Micro/Nano particles simultaneously filled in low-density polyethylene (LDPE) on the space charge characteristics and electrical properties has been investigated by melt blending micro-scale and nanoscale ZnO ...
Jun-Guo Gao +3 more
doaj +1 more source
Highly-visible air-sea rescue marker [PDF]
, 1975 Sea marker is made from sheets of polyolefin material. Material, attached to inflatable polyethylene tube, is coated with bright dye and is effective even in choppy ...
Naimer, J., Radnofsky, M. I.
core +1 more source
Discrete breathers in polyethylene chain
, 2002 The existence of discrete breathers (DBs), or intrinsic localized modes (localized periodic oscillations of transzigzag) is shown. In the localization region periodic contraction-extension of valence C-C bonds occurs which is accompanied by decrease ...
A. V. Savin +13 more
core +1 more source
Rapid, 5 min, low temperature aqueous platinization for plastic substrates for dye-sensitized solar cells [PDF]
, 2019 This paper reports a rapid (5 min), low temperature (120 C) method to platinize the counter electrodes of dye-sensitized solar cell (DSC) devices. This new method uses aqueous solutions and is based on chemical bath deposition of an activating Pd ...
Anthony, RVE +6 more
core +2 more sources