Results 1 to 10 of about 1,374 (132)

Influence of plastic recycling—a feasibility study for additive manufacturing using glycol modified polyethylene terephthalate (PETG)

SN Applied Sciences, 2022
This paper presents a feasibility study for the production of recycled glycol modified polyethylene terephthalate (PETG) material for additive manufacturing.
Mats Bremer, Michael Wahl
exaly   +3 more sources

Prospect for pico-hydropower generation from 3D printed Polyethylene Terephthalate Glycol (PETG) Polymer: A Case Study in Pusu River, Malaysia

Case Studies in Chemical and Environmental Engineering
In Malaysia, rural communities rely on fossil fuel-powered generators for electrification. A small-scale Archimedean Screw Turbine (AST) can be utilized to generate pico-hydropower for potential clean energy generation.
Chuan Choong Yang
exaly   +4 more sources

The Application of Montmorillonite (MMT), Halloysite (HNT), and Carbon Nanotubes (CNT) in Toughened Polyethylene Terephthalate Glycol/Polycarbonate (PETG/PC) Blends: The Critical View on the Use of Nanosized Fillers as Phase Structure Modifiers [PDF]

Polymers
The subject of the conducted study was primarily focused on the development of a new type of polymer blend modified with the use of nanosized fillers. The research concept involved the use of polycarbonate/polyethylene terephthalate glycol (PETG/PC) blends modified with the EBA-GMA impact modifier (ethylene–butylene–acrylonitrile copolymer) and three ...
Adam Piasecki, Jacek Andrzejewski, Piasecki Adam   +2 more
exaly   +4 more sources

Performance Evaluation of Carbon Fiber Reinforced with Polyethylene Terephthalate Glycol (PETG) in Additive Manufacturing [PDF]

E3S Web of Conferences
This research worked on the mechanical properties of Carbon Fiber Reinforced Polyethylene Terephthalate Glycol (PETG) for applications in 3D printing. Carbon fiber reinforcement was incorporated into PETG and pellets as the base material.
Nerella Mary Jasmin, Kumar Rajesh, L. Girisha, Vinoth R., Ram S., Thakur Gaurav, Verma Anjali   +6 more
doaj   +2 more sources

Bond strength of thermoformed and 3D-printed aligners with universal primer versus one-step aligner adhesive with and without sandblasting: An in vitro study. [PDF]

PLoS ONE
ObjectivesChairside bonding of auxiliaries directly to aligners can avoid remanufacturing trays, but optimal protocols may be substrate-specific across modern thermoformed and 3D-printed materials.
Viet Anh Nguyen, Viet Hoang, Thi Quynh Trang Vuong, Thi Nga Phung, Nghi Phan Bich Hoang   +4 more
doaj   +2 more sources

Sustainable Production of Dental and Orthodontic 3D Models Through Fused Granular Fabrication of Recycled Polymers [PDF]

Bioengineering
Sustainable production in dental and orthodontic 3D printing has gained increasing attention due to environmental concerns and the need for cost-effective and resource-saving solutions.
Jens Kruse, Malte Stonis, Julia Barasinski, Florian Konstantin Stangl, Hisham Sabbagh   +4 more
doaj   +2 more sources

The potential of virgin Polyethylene Terephthalate Glycol (PETG) grades and their blends with waste PET(G) for filament-based material extrusion applications

Additive Manufacturing
A commercial low viscosity (LV; eta 0= 255 Pa.s), medium viscosity (MV; eta 0= 574 Pa.s) and high viscosity (HV; eta 0 = 1075 Pa.s) polyethylene terephthalate glycol (PETG) grade, and a high mechanical properties (HMP) PETG grade (eta 0 = 437 Pa.s) are characterized to investigate their applicability for filament-based material extrusion, commercially ...
Lynn Trossaert, Chiara Fiorillo, Ludwig Cardon   +2 more
exaly   +3 more sources

Evaluation of polyethylene terephthalate glycol (PETG), Simubone ™, and photopolymer resin as 3D-printed temporal bone models for surgical simulation

Asian Journal of Surgery
Among types of 3D printing, fused deposition modeling (FDM) and digital light processing (DLP) are the most accessible, making them attractive, low-cost options for simulating surgical procedures. This study characterized and compared inexpensive, synthetic temporal bone models printed using Resin, PETG, and Simubone™.This study compared models made of
Rentor Cafino, Maria Monique Theresita Soliven, Lemuel Clark P Velasco   +2 more
exaly   +3 more sources

Mechanical and dynamic characterization of additively manufactured carbon - reinforced polyethylene terephthalate glycol (PETG) composites

Materials Research Express
The research explores mechanical behavior and dynamic responses of carbon fiber-reinforced polyethylene terephthalate glycol (CF-PETG) composites which were manufactured through Fused Filament Fabrication (FFF) additive manufacturing.
Prabhakaran R, Pitchipoo P, Rajakarunakaran S, Jerold John Britto J   +3 more
doaj   +2 more sources

Valorization of recycled fine powder glass (RFPG) in additive manufacturing: Optimization of the RFPG content in polyethylene terephthalate glycol (PETG) and multi-response analysis

Cleaner Materials
A cyclic economy and sustainability-driven production are key aspects of the industry. Recycled feedstocks are steadily replacing virgin materials to produce parts and as sustainable additives to develop eco-friendly composites. The reinforcing potential of recycled fine powder glass (FPG) on terephthalate glycol (PETG) is investigated.
Markos Petousis, Nikolaos Michailidis, Vassilis Papadakis   +2 more
exaly   +3 more sources