Results 171 to 180 of about 9,958 (229)

Synergy Effect of Synthetic Wax and Tall Oil Amidopolyamines for Slowing Down the Aging Process of Bitumen. [PDF]

Materials (Basel)
Iwański MM, Malinowski S, Maciejewski K, Mazurek G.   +3 more
europepmc   +1 more source

Investigating the performance of asphalt pavements modified with reclaimed asphalt and crumb rubber. [PDF]

Sci Rep
Shams H, Ullah H, Qiu Y, Abdrhman H, Fu J, Yang E.   +5 more
europepmc   +1 more source

Characterization of Bituminous Materials and Their Resistance to Fatigue Cracking by Dissipated Energy in Cyclic Tests: EBADE Test. [PDF]

Materials (Basel)
Pérez-Jiménez FE, Miró R, Martínez AH, López-Montero T, Colás MDM, González-González M, Cabeza-Barahona J.   +6 more
europepmc   +1 more source

Some of the next articles are maybe not open access.

Related searches:

Polymer modified bitumen

Materials Research Innovations, 2012
Standard methods of characterization of bitumen, BIT, and of polymer modified bitumen, PmBs, do not provide sufficient information. We propose to rely on determination of rheological properties which are much more informative. Along theses lines, we have determined rheology before and after the Rolling Thin Film Oven Test, RTFOT.
Ocelić Bulatović, Vesna, Rek, Vesna, Jurkaš-Marković, Kristina   +2 more
openaire   +6 more sources

Polymer Modified Bitumen: Review

Chemistry & Chemical Technology, 2016
The main reasons and ways of bitumen modification by polymers were examined. Positive and negative aspects of the usage of different polymer modifiers (elastomers, thermoplastic elastomers, reactive polymers, thermoplastics) were analysed. The authors’ achievements concerning modification of bitumen by various polymers, namely indene-coumarone ...
Serhiy Pyshyev, Volodymyr Gunka, Yuriy Grytsenko, Michael Bratychak   +3 more
openaire   +1 more source

Polymer-Modified Bitumen Using Ethylene Terpolymers

Petroleum Science and Technology, 2007
Polymer modified bitumen (PMB) is used in various construction applications, especially in motorways. The aim of this study is to improve features of 60/70 penetration grade, modified bitumen used on highways. Increasing the sensitivity to temperature and oxidation resistance are very important points for the modified bitumen.
Keyf, Seyfullah, İsmail, Osman, Çorbacıoğlu, Burcu Didem   +2 more
openaire   +3 more sources

Polymer modified bitumen: Optimization and selection

Materials & Design (1980-2015), 2014
Polymer modification of bitumen has been commonly performed since the 1980s in order to decrease bitumen (and pavement) susceptibility to high and low temperatures, allowing reduction in common failure mechanisms as rutting and cracking. Bitumen modification has been commonly performed by addition of thermoplastic or elastomeric polymers.
JC MUNERA, Alexander Ossa, E.
openaire   +2 more sources

Dynamic mechanical behavior of polymer modified bitumen

Materials Research Innovations, 2002
The dynamic mechanical behaviour of bitumen (BIT) modified with styrene/butadiene/styrene block copolymer (SBS)were investigated. Dynamic mechanical analysis (DMA) were performed in the temperature range -80 to 60 oC. The primary viscoelastic functions were determined at the traffic frequency, 5 Hz.
Rek, Vesna, Barjaktarović, Zrinka
openaire   +2 more sources

Properties of Polymer Modified Bitumen after Rubber-Bitumen Interaction

Journal of Materials in Civil Engineering, 2002
This paper describes results from a laboratory investigation into the effects of the interaction between a styrene-butadiene-styrene (SBS) modified bitumen and recycled crumb rubber on the mechanical performance of impact absorbing asphalt (IAA), an asphaltic material that has applications as a sports and safety surface.
G. D. Airey, T. M. Singleton, A. C. Collop   +2 more
openaire   +1 more source

Polymer‐modified bitumen of recycled LDPE and maleated bitumen

Journal of Applied Polymer Science, 2012
AbstractMaleated bitumen was prepared by the reaction of penetration grade bitumen (80/100) with maleic anhydride at 150°C for 2 h under nitrogen atmosphere. The effectiveness of maleation was assessed in bitumen–recycled low‐density polyethylene (LDPE) blends in terms of their softening point and elastic recovery.
B. Singh, Lokesh Kumar, M. Gupta, G. S. Chauhan   +3 more
openaire   +1 more source