Results 41 to 50 of about 18,433 (253)

Symbolic Regression and Multi‐Objective Optimization of the Flory–Huggins Interaction Parameter for Hydrogels

Advanced Engineering Materials, EarlyView.
We develop a data‐driven method to derive the mathematical expressions of the Flory–Huggins interaction parameter χ for the swelling behavior of temperature–responsive hydrogels. Starting from initial assumptions of χ, our workflow combines Bayesian optimization, Flory–Rehner theory, and symbolic regression to generate candidate χ expressions.
Yawen Wang, Adrian Ehrenhofer, Thomas Wallmersperger   +2 more
wiley   +1 more source

Molecular Dynamics Studies of Shape Memory Polymers: From Bead–Spring Models to Atomistic Simulations

Advanced Engineering Materials, EarlyView.
Coarse‐grained (left) and atomistic (right) models of the shape memory polymer ESTANE ETE 75DT3 are shown schematically. The two representations bridge molecular detail and mesoscopic description. Both models capture shape memory behavior, linking segmental mobility and conformational relaxation of anisotropic chains to macroscopic recovery, and ...
Fathollah Varnik
wiley   +1 more source

Influence of composite resin volume and C-factor on the polymerization shrinkage stress

Brazilian Dental Science, 2016
Objective: Composite polymerization shrinkage stress is an inherent process of chemical and light composite resin activation. Consequently, this fact has been associated to potential clinical problems.
Rafael Francisco Lia Mondelli, Marilia Mattar de Amoêdo Campos Velo, Rafael Simões Gonçalves, Bhenya Ottoni Tostes, Sergio Kiyoshi Ishikiriama, Juliana Fraga Bombonatti   +5 more
doaj   +1 more source

Low Cycle Repetitive Loading of Ti‐6Al‐4V‐Epoxy Composite Lattice Structures for Enhanced Energy Dissipation and Damage Tolerance

Advanced Engineering Materials, EarlyView.
Composite Ti–6Al–4V–epoxy lattice structures are additively manufactured and epoxy infiltrated for cyclic loading. At low lattice volume fractions, hybridization produces synergistic gains in stiffness and energy dissipation. At higher volume fractions, synergy diminishes, although composites still exceed metallic lattices in specific energy ...
Joey Tallon, Jordan Noronha, Justin Dirrenberger, Andrey Molotnikov   +3 more
wiley   +1 more source

Сравнение in vitro полимеризационной усадки реставрационных композитных материалов на основе силорана и метакрилатов

Эндодонтия Today, 2020
Studying polymerization shrinkage composite materials on silorane basis Filtek Silorane, methacrylate composites - high filling QuiXFill (Dentsply) and packed Filtek P-60 (3M ESPE) by a hydrostatic method (Archimedes method) on 36 samples of materials is

doaj  

Experimental Characterization of Mycelium‐Based Composites Under Multiple Loading Conditions

Advanced Engineering Materials, EarlyView.
This study examines the mechanical response of mycelium‐based composites under compression, shear, and tension using mechanical testing and imaging methods. The comparison between unpressed and hot‐pressed specimens shows that hot pressing is associated with higher compression and shear stiffnesses.
Shaghayegh Elahi, Kimiya Tajik, Harvey Shaw, Matti Isakov, Sami Pajunen, Lauri Rautkari   +5 more
wiley   +1 more source

Compatibility of Methacrylate Based Resins Controls Interfacial Failure and Toughness in 3D‐Printed Multimaterial Composites

Advanced Engineering Materials, EarlyView.
This work shows that the mechanical performance of multimaterial digital light processing (DLP) printed thermoset composites is governed by resin compatibility and interfacial design rather than spatial patterning alone. Brittle and ductile resin combinations produced premature interfacial failure, while graded interfaces and mechanically compatible ...
Ahmed M. H. Ibrahim, Li Meng, Ahmad R. Najafi, Nicolas J. Alvarez   +3 more
wiley   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Polymerization shrinkage, flexural and compression properties of low-shrinkage dental resin composites

Dental Materials Journal, 2014
This study evaluated the polymerization shrinkage, flexural and compressive properties of low-shrinkage resin composites. For the study, four methacrylate-based and one silorane-based resin composites were light cured using three different light-curing units (LCUs) and their polymerization shrinkage, flexural (strength (FS) and modulus (FM)) and ...
PARK, Jeong-Kil, LEE, Geun-Ho, KIM, Jong-Hwa, PARK, Mi-Gyoung, KO, Ching-Chang, KIM, Hyung-Il, KWON, Yong Hoon   +6 more
openaire   +3 more sources

Human Gut Bacteria and Lipidic Nanoparticles: Particle Composition Predicts Structural Transformation and Bacterial Biocompatibility

Advanced Functional Materials, EarlyView.
Lipidic nanoparticles (LNPs) were incubated with 21 gut bacteria frequently associated with the human microbiome. SAXS revealed that ∼75% of tested species induced structural transformations in monoolein LNPs, whereas phytantriol and phospholipid formulations remained unaffected.
Jonathan Caukwell, Emily L. Gulliver, Livia Salvati Manni, Frithjof Herb, Caitlin Welsh, Samuel C. Forster, Andrew J. Clulow, Wye‐Khay Fong   +7 more
wiley   +1 more source