Results 61 to 70 of about 19,269 (245)

Electrically Assisted Thermal Stamping of Tunable Carbon‐Based Nanofilms for Direct Fabrication of Hydrophobic, Energy Harvesting, and Sensing Devices

Advanced Materials, EarlyView.
Schematic illustration of the electrically assisted thermal stamping (EATS) method for direct fabrication of carbon‐based nanofilms and their multifunctional applications. Localized Joule heating triggers simultaneous exfoliation, reduction, and fluoropolymer incorporation under ambient conditions, yielding tunable carbon‐based thin‐film coatings ...
Byungseok Seo, Yong Choi, Gajendra S. Shekhawat, Minjoong Shin, Kunmo Koo, Xiaobing Hu, Jiheon Kim, Wonjoon Choi, Xinqi Chen, Vinayak P. Dravid   +9 more
wiley   +1 more source

Scalable and Multifunctional PAN‐MXene Composite Fibers for Thermal Management, Photothermal Conversion, Energy Harvesting, and Sensing for Wearable Applications

Advanced Materials, EarlyView.
Electrospun PAN‐MXene nanofibers and yarns integrate enhanced thermal conductivity, photothermal conversion, and triboelectric energy harvesting within a flexible architecture. Interconnected MXene networks promote efficient phonon transport, while their surface chemistry strengthens tribo‐negative behavior, enabling a high power density of 432.7 mW m ...
Ahmadreza Moradi, Piotr K. Szewczyk, Urszula Stachewicz   +2 more
wiley   +1 more source

Enhancing Grayscale E‐Beam Lithography: Thermal Treatment of Novolak‐Based Resist for 3D Nanostructures

Advanced Materials Interfaces, EarlyView.
Surface roughness and chemistry of novolak‐based grayscale resists are dependent on both exposure dose and post‐exposure thermal treatment. The observed trends align with the viscoelastic phase separation model and underscore the need to consider both thermodynamic and kinetic factors in resist processing. By tailoring thermal treatment, it is possible
Rahul Singh, Christian Vinther Bertelsen, Neeti Kalyani, Maria Dimaki, Winnie Edith Svendsen   +4 more
wiley   +1 more source

Miscibility and specific interactions in blends of poly[(styrene)-co-(cinnamic acid)] with poly(methyl methacrylate) and modified poly(methyl methacrylate)

eXPRESS Polymer Letters, 2007
The miscibility behavior of poly(styrene-co-cinnamic acid) (PSCA) with poly(methyl methacrylate) (PMMA), poly[(methyl methacrylate)-co-(4-vinylpyridine)] (PMMA4VP) and poly[(methyl methacrylate)-co-(2-vinylpyridine)] (PMMA2VP) was studied.
doaj   +1 more source

Scalable, Bottom‐Up Synthesis of Transition Metal–Doped Quantum Confined, 1D Titanate‐Based Lepidocrocite Nanofilaments, Their Electronic Structures and Oxygen Evolution Reactivity

Advanced Materials Interfaces, EarlyView.
Quantum‐confined lepidocrocite titanate nanofilaments are doped, bottom‐up, with Mn+2, Fe+2, Co+2, Ni+2, and Cu+2 to tune electronic structure and catalysis. Doping narrows the bandgap—by up to ∼0.8 eV—and extends visible absorption. Ni‐doped filaments accelerate oxygen evolution (319 mV at 10 mA cm−2) and TM‐doped samples rapidly degrade rhodamine 6G (
Mohamed A. Ibrahim, Devraj Singh, Aidan McMoil, Mary Qin Hassig, Raja Janani, Joshua D. Snyder, Michel W. Barsoum   +6 more
wiley   +1 more source

Fluctuating Curvature and Actuation in 4D Printed Asymmetric Networks by Frontal Photopolymerization

Advanced Materials Interfaces, EarlyView.
Asymmetric polymer networks, fabricated by frontal photopolymerization (FPP), are shown to exhibit curvature oscillations associated with monomer‐solvent exchanges during development and drying. We introduce a theoretical model for such dynamic curvature fluctuations and demonstrate the fabrication of bistable switches and self‐propelled materials that
Muhammad Ghifari Ridwan, Zain Ahmad, Alessandra Vitale, João T. Cabral   +3 more
wiley   +1 more source

Printed Interconnects for Heterogeneous Systems Integration on Flexible Substrates

Advanced Materials Technologies, Volume 10, Issue 6, March 18, 2025.
Key components (sensors, energy devices, communication devices, computing chips, and interconnects) of flexible hybrid electronic (FHE) system connected via conductive printed metal tracks. The figure in the insets shows out‐of‐plane printed interconnects providing opportunities for lithography‐free formation of VIAs, in‐plane access of UTCs pads, and ...
Abhishek Singh Dahiya, Adamos Christou, Sihang Ma, Ravinder Dahiya   +3 more
wiley   +1 more source

Orbital Floor Blowout Fracture Reconstruction Using Moldable Polymethyl Methacrylate: A Report of Two Cases and Their Imaging Findings

, 2022
Majed Fehaid AlSubaie, Abdulaziz Mohammad Al-Sharydah, Hala M Nassim, Abrar Hawsawi   +3 more
openalex   +2 more sources

Advanced Ceramics in Aerospace and Defense: The Interrelationship between Traditional and Additive Manufacturing Approaches

Advanced Materials Technologies, EarlyView.
Additive manufacturing revolutionizes production by enabling on‐demand, customized, and sustainable manufacturing with streamlined supply chains. While metal and polymer AM are well‐established, advanced ceramic AM is rapidly emerging, overcoming traditional material challenges.
Kateryna Oleksandrivna Shvydyuk, Senentxu Lanceros‐Mendez, Abílio Pereira Silva   +2 more
wiley   +1 more source

Thermodynamic and Kinetic Characteristics of Combustion of Discrete Polymethyl Methacrylate Plates with Different Spacings in Concave Building Facades [PDF]

, 2021
Weiguang An, Lujun Peng, Minglun Cai, Kaiyang Hu, Song Li, Tao Wang   +5 more
openalex   +1 more source