Evaluation of the Effect of Titanium Dioxide and Silicon Dioxide Nanoparticles on Impact Strength of Two Commercially Available Heat Cure Acrylic Resins [PDF]
Journal of Clinical and Diagnostic Research, 2022 Introduction: Poor mechanical properties are among the main limitations of denture base resin. There has been a continuous attempt to improve the mechanical properties of denture base resins.
Aparana Sharma +5 more
doaj +1 more source
Clinical Comparison of Low and High Injection Volumes of High-viscosity Bone Cement Used in Percutaneous Vertebroplasty [PDF]
Journal of Minimally Invasive Spine Surgery and Technique, 2021 Objective To compare the clinical effects of different injection volumes of high-viscosity bone cement (polymethylmethacrylate, PMMA) used in percutaneous vertebroplasty (PVP) on the treatment of osteoporotic vertebral compression fractures (OVCF ...
Özkan Özger, Necati Kaplan
doaj +1 more source
New adjuvants on a polymethylmethacrylate base [PDF]
Infection and Immunity, 1976 A new type of adjuvant using influenza virus as an antigen is presented. The new adjuvant was produced by polymerizing monomeric methylmethacrylate in the presence of the antigen. As a comparison, influenza virus was added to previously polymerized polymethylmethacrylate particles.
J, Kreuter, P P, Speiser
openaire +2 more sources
Polymethylmethacrylate Pulmonary Embolism Following Kyphoplasty [PDF]
, 2019 We report a case of polymethylmethacrylate cement pulmonary embolism (PE) that occurred two days following a minimally invasive kyphoplasty procedure. Our patient developed non-specific rib pain postoperatively followed by dyspnea, prompting presentation
Weller, Karl +2 more
core +1 more source
Incorporation versus coating of antimicrobials in polymethylmethacrylate: A systematic review
, 2023 The modification of polymethylmethacrylate will confer antimicrobial resistance to the material and the method of modification, incorporation or coating, can influence the antimicrobial action.
Andréa Cândido dos Reis +2 more
core +1 more source
European Oral Research, 2022 Purpose: Polymethylmethacrylate denture bases are prone to fracture, so reinforcement of dentures with nanoparticles is required to overcome these challenges.
Deepali Barapatre +3 more
doaj +1 more source
New PMMA-Based Hydroxyapatite/ZnFe2O4/ZnO Composite with Antibacterial Performance and Low Toxicity
Biomimetics, 2023 Polymethylmethacrylate (PMMA) is the most commonly used bone void filler in orthopedic surgery. However, the biocompatibility and radiopacity of PMMA are insufficient for such applications.
Olga Bakina +8 more
doaj +1 more source
Sensors, 2019 Parameters to measure nonlinearity in polymethylmethacrylate (PMMA) and carbon fiber reinforced polymer (CFRP) materials have been determined with nonlinear ultrasound (NLUS).
Antonio Callejas, Guillermo Rus
doaj +1 more source
Evaluation of Intramedullary Methods with Polymethylmethacrylate for Fixation of Bone Lesions of the Extremities [PDF]
Revista Brasileira de Ortopedia, 2022 Objective To evaluate the better potential and functional results in pain control in the treatment of pathological fractures and prophylactic fixation with an intramedullary nail associated with polymethylmethacrylate, compared with the utilization of an
Marcio Moura +4 more
doaj +1 more source
Complication of Polymethylmethacrylate Bone Cement in the Mandible
, 2021 Polymethylmethacrylate bone cements have been widely used in orthopedic surgery as well as in maxillofacial area. Despite the advantages, it is well known that acrylic bone cements may cause bone or soft tissue necrosis because of the properties of its ...
Selvi, Fırat +4 more
core +1 more source