Results 201 to 210 of about 411,405 (289)

Experimental study to compare the strength of concrete with different amounts of polypropylene fibers at high temperatures. [PDF]

Sci Rep
Wang Y, Nejati F, Edalatpanah SA, Goudarzi Karim R.   +3 more
europepmc   +1 more source

Toxicity Differences Between Microplastics and Nanoplastics in Organs: From Molecular Mechanisms to Potential Therapeutic Strategies

Med Research, EarlyView.
This review systematically compares the size‐dependent toxicity of microplastics and nanoplastics in the intestine, liver, kidney, lung, and brain. Particle size determines bioavailability, barrier penetration, and injury mechanisms. Because of their small size and high surface reactivity, NPs readily cross the intestinal epithelium and blood–brain ...
Yixian Cheng, Junjie Chen, Rui Fu, Jiawei Zhang, Jianguang Jia, Wei Wang, Zheng Zhang, Peng Zhang, Haosong Chen, Huake Cao, Gang Li, Weiwei Sheng, Ting Li, Bo Chen, Guodong Cao   +14 more
wiley   +1 more source

Synergistic Effects of Polypropylene Fibers and Silica Fume on Structural Lightweight Concrete: Analysis of Workability, Thermal Conductivity, and Strength Properties. [PDF]

Materials (Basel)
Akbulut ZF, Kuzielová E, Tawfik TA, Smarzewski P, Guler S.   +4 more
europepmc   +1 more source

Properties of Lightweight Aggregate Concrete Reinforced with Carbon and/or Polypropylene Fibers. [PDF]

Materials (Basel), 2020
Wei H, Wu T, Yang X.
europepmc   +1 more source

Nonwoven rCF/PA6 Thermoplastic Composites: Hybrid Commingled Fibers vs. Powder Impregnation—Effects on Microstructure and Mechanical Properties

Polymer Composites, EarlyView.
Comparison of powder impregnation and hybrid commingled non‐wovens for PA6/rCF nonwoven composites. The two‐step powder route gives lower voids and higher properties, while the single‐step hybrid route is limited by precursor inhomogeneity and high void content.
Gaia Francesca Lupia, Tommaso Pini, Ilaria Rossitti, Sara Taherinezhad Tayebi, Marco Valente   +4 more
wiley   +1 more source

Second‐Life Thermoset Manufacturing via Mild Solvolysis of Epoxy‐Matrix Composites and Wet‐Laid Mat Production

Polymer Composites, EarlyView.
From end‐of‐life pultruded CFRP profiles (1) to second life composites (7) through mild solvolysis (2,3), wet‐laid nonwoven mat fabrication (4), resin impregnation (5), and compression molding (6). ABSTRACT The growing use of carbon fiber–reinforced thermosets has led to the accumulation of significant composite waste, posing environmental and economic
Ehsan Zolfaghari, Fabian Rechsteiner, Violetta Schumm, Emanuela Muscolino, Sabina Alessi, Nadka Tz. Dintcheva, Clelia Dispenza   +6 more
wiley   +1 more source

The Effect of the Addition of Polypropylene Fibers to Primer on the Pull-Off Strength of Epoxy Resin Coatings. [PDF]

Materials (Basel), 2020
Kampa Ł, Chowaniec A, Królicka A, Sadowski Ł.   +3 more
europepmc   +1 more source

Acrylonitrile Styrene Acrylate (ASA) With Optimized Aluminum Oxide (Al2O3) Nanofiller Content for MEX Additive Manufacturing: Thermomechanical, Rheological, and Quality Metrics

Polymer Composites, EarlyView.
Characterization processes for ASA/Al2O3 nanocomposites in MEX 3D printing. ABSTRACT As additive manufacturing (AM) continues to expand, the demand for durable components for outdoor applications is increasing. Acrylonitrile styrene acrylate (ASA), a weather‐resistant polymer, is widely used in these applications, and improving its performance could ...
Nectarios Vidakis, Markos Petousis, Nikolaos Michailidis, Emmanuel Stratakis, Vassilis M. Papadakis, Maria Spyridaki, Aikaterini Gkagkanatsiou, Apostolos Argyros, Nektarios K. Nasikas   +8 more
wiley   +1 more source

Evaluating the suitability of incorporating sugarcane bagasse ash, polypropylene fibers, and sea sand-seawater in enhancing physico-mechanical properties of lightweight foamed concrete. [PDF]

Sci Prog
Chau VN, Ho LS, Hoang TQ, Dang VQ.
europepmc   +1 more source

Basalt Fiber Surface Modification for Improved Interaction With Polyamide‐6 for High‐Performance Automotive Applications

Polymer Composites, EarlyView.
Amino‐silane treatment improves the basalt fiber–PA6 interface, enhancing composite performance. ABSTRACT Basalt fiber‐reinforced polymer (BFRP) composites have emerged as sustainable alternatives to glass fiber (GF) composites, but their performance is often controlled by the quality of the fiber–matrix adhesion.
Mohammad Mezbah Ul Hoque, Manuel Garcia‐Perez, Manuel Raul Pelaez‐Samaniego, Vikram Yadama   +3 more
wiley   +1 more source