Results 161 to 170 of about 225,323 (289)

Mechanically Robust and Biodegradable Electrospun Membranes Made from Bioderived Thermoplastic Polyurethane and Polylactic Acid [PDF]

Robert Chambers, Bhausaheb S. Rajput, Gordon B. Scofield, Jaysen Reindel, Katherine O’Shea, Richey Jiang Li, Ryan Simkovsky, Stephen P. Mayfield, Michael D. Burkart, Shengqiang Cai   +9 more
openalex   +1 more source

Durable Electro‐Photothermal Superhydrophobic Coatings Based on Liquid‐Like Functionalization of Nanoparticles: Improved Water Repellency and Droplet Rebound

Advanced Materials Interfaces, EarlyView.
Multi‐walled carbon nanotubes (CNTs) are functionalized with liquid‐like linear polydimethylsiloxane (LPDMS) brushes and conventional solid‐like alkyl brushes, then incorporated into a resin and spray‐coated onto substrates. The resulting surfaces exhibit distinct water‐repellent behaviors.
Amirhossein Jalali Kandeloos, Tanja Eder, Youven Benseghir, Michael R. Reithofer, Manuel Luitz, Jia Min Chin   +5 more
wiley   +1 more source

Dynamically crosslinked-interpenetrating networks for sustainable 3D-printed elastomeric foams. [PDF]

Nat Commun
Peng S, Zheng X, Liu C, Yang J, Lin E, Huang X, Weng Z, Zheng L, Chen W, Peng X, Wu L.   +10 more
europepmc   +1 more source

Treatment with Plasma Activated (Salt) Water Sterilizes Macromolecular Coatings While Maintaining Their Integrity and Functionality

Advanced Materials Interfaces, EarlyView.
PDMS samples were covalently coated with mucin glycoproteins and then treated with either plasma activated water (PAW) or saline (PAS) as a means of disinfection. The samples could be successfully sterilized without compromising the structural integrity or functionality of those coatings.
Bernardo Miller Naranjo, Markus Ahrens, Ádám Nemes, Petra Mela, Oliver Lieleg   +4 more
wiley   +1 more source

Polyurethane Flexible Joints as an Advanced Adhesive Layer in Sustainable Prefabricated Small Bridge Structures. [PDF]

Materials (Basel)
Jasińska D, Szeptyński P, Pochopień JG, Kwiecień A.   +3 more
europepmc   +1 more source

Microstructure Evolution of Reactive Polyurethane Films During In Situ Polyaddition and Film‐Formation Processes [PDF]

Huimin Duan, Shuli Li, Jinbiao Zhao, Hao Yang, Heyang Tang, Dongming Qi, Zhichao Huang, Xinxin Xu, Lei Shi, Peter Müller‐Buschbaum, Qi Zhong   +10 more
openalex   +1 more source

Ultra‐Improved Interfacial Strength Between Metallic Surface and Polyurethane via Cost‐Effective Anodizing Process

Advanced Materials Interfaces, EarlyView.
SAA significantly enhanced Al/PU bonding, increasing SLSS by up to 920% and fracture energy by 15 100% through optimized micro‐nano porous surfaces. RSM identified the optimal anodizing conditions, while ML confirmed sulfuric acid concentration and roughness as dominant predictors of strength.
Umut Bakhbergen, Sherif Araby, Zhandos Tauanov, Nursultan Turdakyn, Reza Montazami, Fethi Abbassi, Gulnur Kalimuldina   +6 more
wiley   +1 more source

Response to Commentary on "Effectiveness of a Single-Use Polyurethane Foam Positioning Pad Compared With Five-Layer Foam Sacral Dressing for Pressure Ulcer Prevention in the Operating Room: A Randomized Controlled Clinical Trial". [PDF]

Health Sci Rep
Elhihi EA, Almuwallad SA, Alqrashi BM, Nada EM, Alduaiji NA, Alfakeeh AA.   +5 more
europepmc   +1 more source

Oligoetherols and polyurethane foams obtained from metasilicic acid [PDF]

, 2017
Ewelina Chmiel, Jacek Lubczak
openalex   +1 more source

A Sleeve Alters the Pressure‐Stretch Curve of a Hyperelastic Balloon to Enable Pre‐Programmed Sequencing

Advanced Materials Technologies, Volume 10, Issue 6, March 18, 2025.
This article demonstrates that encasing a hyperelastic balloon in an inextensible sleeve greatly increases its burst pressure. This simple mechanical behavior can be used to produce an asymmetric inflation‐deflation sequence for coupled balloons with different thicknesses so they could serve as a soft robot's rear and front anchors when driven from a ...
Ifat Gertler, Katherine J. Kuchenbecker
wiley   +1 more source