Results 11 to 20 of about 110 (94)
Clinical Insights From an 11-Year and 6-Month Follow-Up of a Full-Mouth Lithium Disilicate Rehabilitation for Severe Tooth Wear. [PDF]
J Esthet Restor DentABSTRACT Objective This article aims to describe the clinical execution and management of a full‐mouth rehabilitation in a patient with severe tooth wear, utilizing partial and full‐contour lithium disilicate restorations, with a long‐term follow‐up of 11 years and 6 months.
Reis JMDSN +4 more
europepmc +2 more sources
Minimally Invasive Ceramic Laminate Veneers for Maxillary Anterior Esthetic Rehabilitation: A 12+ Years Follow-Up. [PDF]
J Esthet Restor DentABSTRACT Objective This case report describes an esthetic rehabilitation focused on closing diastemas and improving tooth morphology to restore smile harmony using thin porcelain laminates. The advantages, limitations, and characteristics of feldspathic ceramics in laminate fabrication are discussed, highlighting their importance in minimally invasive ...
Reis JMDSN +3 more
europepmc +2 more sources
Evaluating the Probability of Survival and Damage Mechanisms of Resin Matrix Ceramics: Insights Into Wear Progression and Surface Damage Under Fatigue. [PDF]
J Esthet Restor DentABSTRACT Objective This study evaluated the probability of survival, failure modes, and fatigue‐induced wear progression, as well as assessed damage tolerance under simulated mastication in two resin matrix ceramics (polymer‐infiltrated ceramic networks (PICN) and resin nanoceramic (RNC)).
Ruggiero MM +3 more
europepmc +2 more sources
Esthetic Rehabilitation of the Smile with No-Prep Porcelain Laminates and Partial Veneers. [PDF]
Case Rep Dent, 2015 Rehabilitation of patients with anterior conoid teeth may present a challenge for the clinician, especially when trying to mimic the nature with composite resins. This clinical report exemplifies how a patient with conoid upper lateral incisors was rehabilitated with minimally invasive adhesive restorations.
Farias-Neto A +4 more
europepmc +2 more sources
International Scholarly Research Notices, Volume 2015, Issue 1, 2015., 2015 Objectives. This study evaluated the influence of cavity surface finishing with diamond burs of different grit mounted on high‐speed turbine and ultrasound on the roughness and microshear bond strength (MBS) of a lithium silicate glass‐ceramic to enamel and dentin. Methods.
Carla Castiglia Gonzaga +8 more
wiley +1 more source
Revista Catarinense da Ciência Contábil, 2013 O artigo tem por objetivo estruturar uma proposta de implementação do custeio baseado em atividades na gestão de serviços odontológicos. Foi realizada uma pesquisa descritiva, por meio de um estudo de caso, com abordagem predominantemente qualitativa.
Karyn de Castro Serratine +1 more
doaj +1 more source
DENS, 2006 O presente trabalho teve por objetivo avaliar a distribuição de tensões nos dentes restaurados com facetas de porcelana pelo método de elementos finitos, em modelos representativos de incisivos centrais superiores onde foram utilizados três tipos de simulações: dentes que não apresentavam preparos dentários com e sem recobrimento da borda incisal, e ...
João Luiz Neves PEREIRA +1 more
openaire +2 more sources
Influence of in vitro pigmenting of esthetic orthodontic ligatures on smile attractiveness
Dental Press Journal of Orthodontics, 2012 OBJECTIVE: To evaluate the perception of dental students and orthodontists on the degree of influence that pigmented esthetic elastic ligatures have on smile attractiveness, by judging clinical photographs. METHODS: Sixteen clinical facial photographs of
Camila Ferraz +2 more
doaj +1 more source
Journal of Applied Oral Science, 2006 INTRODUCTION: Esthetic post and core systems were recently introduced. There are few reports regarding their behavior under cyclic loading. OBJECTIVES: This study compared the effect of cyclic loading on survival rate, residual strength and mode of ...
Anuar Antônio Xible +4 more
doaj +1 more source
Journal of Biomedical Materials Research Part B: Applied Biomaterials, Volume 113, Issue 10, October 2025.ABSTRACT This study evaluates the effect of varying resin composite thicknesses for sealing the screw‐access hole of zirconia abutments on the fatigue mechanical behavior of a lithium disilicate cement‐retained material. One hundred lithium disilicate discs (Ø = 10 mm, 1 mm thickness; IPS e.max CAD, Ivoclar AG) were prepared, alongside zirconia ...
Maria Gabriela Packaeser +7 more
wiley +1 more source