Results 81 to 90 of about 179,487 (256)
Multimodal Data‐Driven Microstructure Characterization
Advanced Engineering Materials, EarlyView.A self‐consistent autonomous workflow for EBSP‐based microstructure segmentation by integrating PCA, GMM clustering, and cNMF with information‐theoretic parameter selection, requiring no user input. An optimal ROI size related to characteristic grain size is identified.
Qi Zhang +4 more
wiley +1 more source
Compressive strength and specific strength of porous nickel foam/resin composite material
Cailiao gongchengThe nickel foam （the average pore diameter is about 2.7 mm，and the porosity is 93.1%） is used for the epoxy resin to coat the pore-struts， and the porous nickel foam/epoxy resin composite is obtained with such pore-struts as a multi-layer structure.
LIU Peisheng +4 more
doaj +1 more source
Cavitation in a soft porous material. [PDF]
PNAS Nexus, 2022 Leng Y, Vlachos PP, Juanes R, Gomez H.
europepmc +1 more source
Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing
Advanced Engineering Materials, EarlyView.The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai +6 more
wiley +1 more source
Analysis on the Flow in Storage Tank with Porous Material Filled Fluid Boundary Layer
Shiyou jixie, 2018 Few literatures have reported on the filling of porous materials in LNG storage tanks. In view of this, a two-dimensional model of turbulent flow in porous media is established using Fluent 6.3.
Zhang Shushu, Xing Zhixiang, Zhang Jian
doaj
Damage behavior of cold-rolled sintered fiber felts
Materials Research ExpressPorous Materials, such as sintered fiber felts (SFFs), can contribute to the reduction of aircraft noise by acting as a low-noise trailing edge (TE).
J Tychsen, J M Lück, J Rösler
doaj +1 more source
Frontiers in MaterialsBenzene is a prevalent environmental contaminant, and its effective removal through adsorption is crucial to mitigate both environmental and health impacts.
Jiali Li +7 more
doaj +1 more source
Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites
Advanced Engineering Materials, EarlyView.Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter +9 more
wiley +1 more source
Efficacy of Antimicrobials Against Enveloped and Non-Enveloped Viruses on Porous Materials: A Review
MicroorganismsFomites are common vehicles for viral transmission. Most studies on virus disinfection have focused on non-porous, hard surfaces, with few investigating porous materials.
Jinge Huang +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.The present study investigates recycling of NiTi shape memory alloys via vacuum induction melting. An ingot was synthesized from elemental Ni and Ti and subjected to three subsequent remelting cycles. Remelting increases process durations and impurity levels and adversely affects microstructures and functional properties.
Sakia Sophia Noorzayee +7 more
wiley +1 more source