Results 181 to 190 of about 170,252 (259)

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Carboxylic‐Acid Functionalized Multiwalled Carbon Nanotube‐Alkane‐Based Resistive Temperature Sensor for Cold Chain Applications

Advanced Engineering Materials, EarlyView.
This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera, Philippe Marrec, A. Jorge Parola, Madalena Dionísio, Hugo Águas, Andreia F. M. Santos, Hamed Pourkheirollah, Donald Lupo, César A. T. Laia   +8 more
wiley   +1 more source

Evaluation of positioning accuracy, radiation dose and image quality: artificial intelligence based automatic versus manual positioning for CT KUB. [PDF]

F1000Res
Kundu S, Nayak K, Kadavigere R, Pendem S, Priyanka.   +4 more
europepmc   +1 more source

Planar Solid‐State Nanopores Toward Scalable Nanofluidic Integration Based on CMOS Technology

Advanced Engineering Materials, EarlyView.
We present a scalable silicon‐based fabrication strategy for planar solid‐state nanopores to enable their integration with complex nanofluidic systems. Prototype devices demonstrate normal voltage‐current characteristics, good noise performance, and appreciable streaming currents. Our CMOS‐compatible fabrication process offers precise geometric control
Ngan Hoang Pham, Chenyu Wen, Mohammad Hadi Khaksaran, Won‐Yong Lee, Javier Cruz, Klas Hjort, Dongping Wu, Shi‐Li Zhang   +7 more
wiley   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Evaluation of positioning accuracy in head-and-neck cancer treatment: A cone beam computed tomography assessment of three immobilization devices with volumetric modulated arc therapy. [PDF]

J Biol Methods
Mail N, Alshamrani KM, Lodhi RN, Khawandanh E, Saleem A, Khan B, Alghamdi M, Nadershah M, Althaqafy MS, Subahi A, Alghamdi SM.   +10 more
europepmc   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

A Workflow to Accelerate Microstructure‐Sensitive Fatigue Life Predictions

Advanced Engineering Materials, EarlyView.
This study introduces a workflow to accelerate predictions of microstructure‐sensitive fatigue life. Results from frameworks with varying levels of simplification are benchmarked against published reference results. The analysis reveals a trade‐off between accuracy and model complexity, offering researchers a practical guide for selecting the optimal ...
Luca Loiodice, Krzysztof S. Stopka, Michael D. Sangid   +2 more
wiley   +1 more source

A Compact Spin‐Coated Graphene UWB Antenna for Breast Tumor Detection

Advanced Engineering Materials, EarlyView.
A compact, spin‐coated graphene ultra‐wideband patch antenna designed for breast tumor detection, capable of distinguishing between malignant and benign tumors. This innovative antenna can serve as an effective initial screening tool, particularly in resource‐limited settings such as rural areas, where access to advanced medical equipment like MRI and ...
Raja Rashidul Hasan, Shuvra Saha, Sumit Hassan Eshan, Rinku Basak, Md. Nahian Al Subri Ivan, Ahmed Murtuza Saleque, Raja Tariqul Hasan Tusher, Sadia Zabin, Md. Abdur Rahman, Yuen Hong Tsang   +9 more
wiley   +1 more source

Prediction of Surface Topography Parameters in Direct Laser Interference Patterning of Stainless Steel Using Infrared Monitoring and Convolutional Neural Networks

Advanced Engineering Materials, EarlyView.
This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky, Marcelo Sallese, Leander Kläber, Clemens Kuhn, Keming Du, Andrés Fabián Lasagni   +5 more
wiley   +1 more source