Results 91 to 100 of about 55,552 (255)

Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition

Advanced Engineering Materials, EarlyView.
A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley   +1 more source

Toward a certification protocol for Positive Energy Districts (PED). A methodological proposal

TeMA: Journal of Land Use, Mobility and Environment
In order to achieve the ambitious CO2 emission reduction targets, set by the Sustainable Development Goals, it is crucial to act on cities. Indeed, cities are responsible for 67% of the world's primary energy consumption and about 70% of energy-related ...
Marco Volpatti, Elena Mazzola, Marta Carla Bottero, Adriano Bisello   +3 more
doaj   +1 more source

Composition‐Tuned Enhancement of the Anomalous Nernst Effect in FeCo–Pt Thin Films on Rigid and Flexible Substrates

Advanced Engineering Materials, EarlyView.
Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi, Hiroyuki Awano, Kenji Tanabe   +2 more
wiley   +1 more source

Heat demand mapping and district heating grid expansion analysis: Case study of Velika Gorica

E3S Web of Conferences, 2017
Highly efficient cogeneration and district heating systems have a significant potential for primary energy savings and the reduction of greenhouse gas emissions through the utilization of a waste heat and renewable energy sources.
Dorotić Hrvoje, Novosel Tomislav, Duić Neven, Pukšec Tomislav   +3 more
doaj   +1 more source

Incorporation of Selenium into Sol–Gel‐Derived Bioactive Glass: Influence on Glass Structure, Bioactivity, and its Selective Cytotoxicity

Advanced Engineering Materials, EarlyView.
Selenium was incorporated into a sol–gel‐derived bioactive glass to enable sustained therapeutic ion release. The selenium‐containing glass preserved bioactivity while selectively inducing cytotoxicity in osteosarcoma cells and maintaining osteoblastic viability.
Breno Rocha Barrioni, Thalita Marcolan Valverde, Talita Martins, Guilherme Mattos Jardim Costa, Alfredo Miranda de Goes, Marcello Rosa Dumont, Eduardo Henrique Martins Nunes, Marivalda de Magalhães Pereira   +7 more
wiley   +1 more source

Solid‐State Diffusion and Intermetallic Phase Formation in Roll‐Bonded Mg–Zn Composites With Kirigami‐Patterned Inlay

Advanced Engineering Materials, EarlyView.
Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov, Oleksandr Bobukh, Christian Klose, Florian Nürnberger, Hans Jürgen Maier   +4 more
wiley   +1 more source

Rafting of Ni‐Based Superalloys Under Multiaxial Load as Understood by Phase‐Field Simulations and Critical Experiments

Advanced Engineering Materials, EarlyView.
Phase‐field simulations coupled with dislocation‐density‐based crystal plasticity modeling reproduce γ′ rafting behavior in single‐crystal Ni‐based superalloys under varied loading conditions. The model captures both macroscopic creep and microscopic morphology evolution, with results matching high‐temperature creep experiments.
Micheal Younan, David Bürger, Gunther Eggeler, Oleg Shchyglo, Ingo Steinbach, Muhammad Adil Ali   +5 more
wiley   +1 more source

Energy Management System for a Residential Positive Energy District Based on Fuzzy Logic Approach (RESTORATIVE)

Smart Cities
There is a clear European Strategy to transition by 2050 from a fossil fuel-based economy to a completely new system based on renewable energy resources, with electricity as the main energy carrier.
Tony Castillo-Calzadilla, Jesús Oroya-Villalta, Cruz E. Borges   +2 more
doaj   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source

Phase Field Failure Modeling: Brittle‐Ductile Dual‐Phase Microstructures under Compressive Loading

Advanced Engineering Materials, EarlyView.
The approach by Amor and the approach by Miehe and Zhang for asymmetric damage behavior in the phase field method for fracture are compared regarding their fitness for microcrack‐based failure modeling. The comparison is performed for the case of a dual‐phase microstructure with a brittle and a ductile constituent.
Jakob Huber, Jan Torgersen, Ewald Werner
wiley   +1 more source