Results 61 to 70 of about 14,800,641 (243)
Simultaneous effect of welding current with post-weld T6 heat-treatment on corrosion susceptibility of Al6013 alloy joined by GTAW [PDF]
Al6013 base metals were joined successfully with ER4047 weld metal by using the GTAW method under different welding currents. Post-weld T6 heat treatment effects on corrosion properties were investigated in terms of open circuit potential (OCP ...
Topuz, Mehmet, Mehmet TOPUZ
core +2 more sources
The present work has been conducted in order to determine the influence of heat treatment on the wear and corrosion behaviours of a gray cast iron substrate coated with a Ni base coating deposited by HVOF thermal spray.
A. Öz +5 more
doaj
The microstructure and properties of the heat affected coarse grain zone of steel 07MnCrMoVR with post¬weld heat treated at 460 ~ 660 °C for 2 h are analyzed by means of optical microscope, scanning microscope, transmission electron microscope and impact
冯路路, 乔文玮, 鲁修宇, 周峰
doaj
This study aimed to compare the fatigue resistance of files made from different heat treatment methods and surface treatment. Four prototype files were created through heat treatment and titanium coating surface treatment (AT, DT, ER, EN; named ...
Jung-Hong Ha +11 more
core +1 more source
Simulation of Duplex Heat Treatment Nb3Sn Compounds in Cu-Nb-Sn Superconducting Multifilamentary Wire [PDF]
Nb3Sn is intermetallic compounds being used as superconductor formed by diffusion of Sn through grain boundary during internal tin process. It was known that grain boundary diffusion is dominant among any other mechanism.
Arimaz , Hangga +2 more
core +1 more source
Study on Welding Process of Solid Phase Welding by Post Heat Treatment
固相圧接における後熱温度,後熱時間,接合変形度の影響を検討した結果,次のような結論を得た.1.後熱処理による接合状況の進行過程は,後熱温度,後熱時間,接合変形度によって左右され,アレニウスの式を満足する.2.後熱初期の回復現象によって起る接合部に残留する弾性応力の緩和と,さらには後続する再結晶現象によって,接合境界の原子の移動,再配列が進み接合強さは向上する.3.接合境界状態の改善と母材の軟化現象との総合効果によって,継手の機械的性質は決定し,材質,接合変形度,温度によって定まるほぼ一定の後熱時間で最大値がえられた.4.後熱温度が高くなると,空洞の球状化および集合が起る結果,軟化によって低下した接合強さに再び増加が認められ,接合変形度の差の影響はなくなる傾向にある.
Hashimoto, Tatsuya, Ohashi, Osamu
openaire +2 more sources
Consideration of residual stress and geometry during heat treatment to decrease shaft bending [PDF]
In automotive industry, heat treatment of components is implicitly related to distortion. This phenomenon is particularly obvious in the case of gearbox parts because of their typical geometry and precise requirements.
SURA, Edoardo +3 more
core +1 more source
Research Progress and Prospects of Wood High-temperature Heat Treatment Technology
High temperature heat treatment is one of the main technologies with the highest market conversion rate and broad future prospects in the functional technology of wood. Chemical reagents are not added in the production process. The treatment improves the
Shuai Cao, Jiabin Cai, Shuai Cheng
core +1 more source
The unique thermal history of selective laser melting (SLM) can lead to high residual stress and a non-equilibrium state in as-fabricated titanium alloy components and hinders their extensive use.
Liu, Jianwen +15 more
core +1 more source
Effect of Heat Treatment on Performance of 2205 Base Equipment and Pipes
2205 dual‐phase stainless steel is widely used in petrochemical equipment. This paper simulates welding, post‐weld heat treatment, and operation conditions of 2205 steel.
Yajun Li +4 more
doaj +1 more source

