Results 121 to 130 of about 154,655 (285)

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

Thermodynamic Pathways of Nonequilibrium Solidification in Wire‐Arc Additive Manufacturing Fe‐Based Multicomponent Alloy Structures

Advanced Engineering Materials, EarlyView.
Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios, Anthony Gonzalez, Aleksander Aleman, Tyler Dolmetsch, Tanaji Paul, Arvind Agarwal   +5 more
wiley   +1 more source

Air‐Pressure–Actuated Vibroacoustic Metamaterial With Tunable Bandgap: Design, Modeling, and Characterization

Advanced Engineering Materials, EarlyView.
This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal, Michael M. Becker, Sarah C. L. Fischer   +2 more
wiley   +1 more source

Composition‐Tuned Enhancement of the Anomalous Nernst Effect in FeCo–Pt Thin Films on Rigid and Flexible Substrates

Advanced Engineering Materials, EarlyView.
Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi, Hiroyuki Awano, Kenji Tanabe   +2 more
wiley   +1 more source

Load Mismatch Compensation of Load-Modulated Power Amplifiers: A Comprehensive Review

Energies
With the diversification, acceleration, and arraying of wireless communication systems, power amplifiers (PAs) face stricter demands in terms of RF operation bandwidth, high-efficiency power range, and load mismatch compensation.
Yufeng Zang, Weimin Shi, Jinting Liu, Tian Qi, Mingyu Li   +4 more
doaj   +1 more source

Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland, Finn‐Lennard Janthur, Sarah Seffer, Jörg Hermsdorf, Ludger Overmeyer, Annika Raatz   +5 more
wiley   +1 more source

Novel Tailoring of Ternary ZnS‐MXene‐TiO2 Nanocomposite Heterojunction and Its Tunable Electrochemical Properties With Enhanced Photocatalytic Degradation

Advanced Engineering Materials, EarlyView.
ZnS‐MXene‐TiO2 nanocomposite heterojunction for photocatalytic decomposition of this methylene blue dye (MB) greatly improves light absorption, charge separation, and active site area. Two‐dimensional MXene forms nanocomposites by easily combining them with 0D (quantum dots), 1D (tube and wire), 2D (plane and sheet), and 3D (particle and lamellar ...
Latiful Kabir, Dohyun Kim, Minho Song, Jae Doc Na, Young Jun Joo, Kwang Youn Cho, Karna Wijaya, Won‐Chun Oh   +7 more
wiley   +1 more source

Few-cycle Yb-doped laser sources for attosecond science and strong-field physics

APL Photonics
Yb-doped laser amplifiers have, in recent years, found applications in attosecond science, driven largely by the opportunities associated with high-average-power and high-repetition-rate attosecond sources.
Tran-Chau Truong, Dipendra Khatri, Christopher Lantigua, Chelsea Kincaid, Michael Chini   +4 more
doaj   +1 more source

Assessing Altered Coating Adhesion on Plasma‐Deoxidized Surfaces Under Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
This study demonstrates the effectiveness of atmospheric pressure plasma pretreatment in modifying silicon and stainless steel surfaces to improve adhesion. Argon‐hydrogen plasma increases surface roughness and improves adhesion strength, whereas pure argon results in smoother surfaces and structural changes.
Selina Raumel, Lara Kuhr, Khemais Barienti, Sebastian Herbst, Florian Nürnberger, Hans Jürgen Maier, Marc C. Wurz   +6 more
wiley   +1 more source

Productivity‐Driven Optimization of Laser Powder Bed Fusion Parameters for IN718 Superalloy: Process Control, Microstructure, and Mechanical Properties

Advanced Engineering Materials, EarlyView.
This study demonstrates how optimizing laser power, scanning speed, and hatching distance in laser powder bed fusion can boost the productivity of Inconel 718 manufacturing by up to 29% while maintaining mechanical integrity. The work delivers a validated process window and cost–time analysis, offering industry‐ready guidelines for efficient additive ...
Amir Behjat, Guido Barale, John Stavridis, Ehsan Norouzi, Jin‐Yoo Suh, Dong‐Ik Kim, Luca Iuliano, Abdollah Saboori   +7 more
wiley   +1 more source