Results 221 to 230 of about 10,090,929 (261)
Some of the next articles are maybe not open access.

Session 12 overview: Efficient Power Conversion

2016 IEEE International Solid-State Circuits Conference (ISSCC), 2016
The session on Efficient Power Conversion is about improvement of efficiency and versatility in switched-capacitor, inductor-based DC-DC converters, and LED drivers. The first two papers address switched-capacitor power conversion, dealing with loss mechanisms and limited ratios.
Vadim Ivanov, Jaejin Park
openaire   +1 more source

Efficiency improvement of power conversion system with multilayer power inductor

2020 IEEE International Conference on Consumer Electronics - Asia (ICCE-Asia), 2020
In this paper, the multilayer power inductor with the air-clip is designed and fabricated to improve the saturation current of power inductor for the power conversion system. It is proved that the air-clip is able to influence the saturation current of power inductor and the efficiency of the power conversion system.
Hyun Gyu Jang   +5 more
openaire   +1 more source

On structural effects and energy conversion efficiency of power harvesting

SPIE Proceedings, 2008
The concept of power harvesting works towards developing self-powered devices that do not require replaceable power supplies. One important parameter defining the performance of a piezoelectric power harvesting system is the efficiency of the system. However, an accepted definition of energy harvesting efficiency does not currently exist.
null Yabin Liao, Henry A. Sodano
openaire   +1 more source

Optimization of klystron power conversion efficiency

1966 International Electron Devices Meeting, 1966
Optimum power conversion efficiency in klystrons involves two factors: (1) electron bunching, for highest current conversion efficiency, and (2) minimum velocity spread, for optimum energy removal in the output gap. The merit figure, a new criterion involving both of these factors, is shown to give an excellent quantitative indication of klystron power
openaire   +1 more source

CuGaSe 2 solar cells with 9.7% power conversion efficiency

Applied Physics A: Materials Science & Processing, 1996
Heterojunctions, such as ZnO/CdS/CuGaSe2, were fabricated for photovoltaic applications. Optimization of device structures based on monocrystalline CuGaSe2 led to the highest-to-date power conversion efficiencies for CuGaSe2 solar cells. At room temperature under 100 mW/cm2 AM1.5 illumination a maximum cell efficiency of 9.7% was achieved, given by an ...
M. Saad   +3 more
openaire   +1 more source

Power Chips for Efficient Energy Conversion

AIP Conference Proceedings, 2004
The Power Chips technology employs a gap of 4–10 nanometers in a gap diode to allow for efficient thermal conversion with very low thermal leakage. The design ΔT is on the order of 400 degrees single stage, with operation possible from 1 K to 1600 K, depending on configuration and meeting engineering challenges.
openaire   +1 more source

Efficiency of Traction Power Conversion Based on Crosswind Motion

2013
This review paper is devoted to analytical modeling of the so-called kite wind generator (KWG) whose power conversion operation uses a tethered kite to mechanically drive a groundbased electric generator. An important aspect of the KWG operating principle is the controlled crosswind motion of the kite, which is used to increase the kite traction force.
Ivan Argatov, Risto Silvennoinen
openaire   +1 more source

Efficiency Regulations: Driving power conversion efficiency designs

IEEE Power Electronics Magazine, 2017
In recent decades, government agencies developed programs to improve the efficiency of our electronic products and appliances. A 1999 study estimated that up to 10% of electricity consumed by residential products was wasted when products had been turned off by consumers [1].
openaire   +1 more source

Power Gallium Nitride Technology: The Need for Efficient Power Conversion

IEEE Electrification Magazine, 2020
The biggest motivation and driver for semiconductor power device innovation is improved efficiency in power conversion. Power gallium nitride (GaN) technology shows the greatest performance benefits against other incumbent technologies, including silicon (Si) technology. A reduction in power losses is the key challenge industries are facing.
openaire   +1 more source

Photovoltaic power conversion with efficiency weight optimisation

IEEE International Conference on Industrial Technology, 2003, 2004
Photovoltaic power conversion systems for power rating of about 2.5 kW consist generally of a step-up converter, a DC-AC inverter for 5 Hz and the transformer coupling to the grid. Potential separation is required between the modules and grid. A standard 5 Hz transformer can accomplish this separation.
E. Winfried, H. Weiss
openaire   +1 more source

Home - About - Disclaimer - Privacy