Results 201 to 210 of about 2,841,897 (254)

A Paper-Based Wearable Moist-Electric Generator for Sustained High-Efficiency Power Output and Enhanced Moisture Capture. [PDF]

Small
Gao Y, Elhadad A, Choi S.
europepmc   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Modification of glass screen printed electrodes with graphene quantum dots for enhanced power output in miniaturized microbial fuel cells. [PDF]

Sci Rep
Mao YM, Amreen K, Calay RK, Banerjee A, Goel S.   +4 more
europepmc   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

Cardiac power output associated with hospitalization and mortality in coronary artery disease patients at stage B heart failure. [PDF]

Int J Cardiol Heart Vasc
Hsieh MJ, Yeh JK, Huang YC, Ho MY, Chen DY, Lee CH, Wang CY, Chang SH, Chen CC, Hsieh IC.   +9 more
europepmc   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

Influence of Conventional Resistance Training Compared to Core Exercises on Road Cycling Power Output. [PDF]

Cureus
Sitko S, López-Laval I, Cirer-Sastre R.
europepmc   +1 more source

Enhanced Gamma Radiation Shielding Using Epoxy Quartz Fabric Composites Reinforced With CoCl2 Microparticles

Advanced Engineering Materials, EarlyView.
The growing demand for lightweight, nontoxic, and multifunctional gamma shielding materials has intensified efforts to find alternatives to conventional lead and aluminum‐based protectants. In this work, we develop epoxy quartz fabric composites reinforced with cobalt chloride (CoCl2) microparticles, fabricated via hand lay‐up with varying filler ...
Summan Urooge, Ahsan Irshad, Umar Jamil, Srosh Fazil, Khuram Liaqat, Kashif Shahzad, Fakhar Alam, Mehboob Alam   +7 more
wiley   +1 more source

Cardiac power output ratio: Novel survival predictor after percutaneous ventricular assist device in cardiogenic shock. [PDF]

ESC Heart Fail
Leung C, Wong IMH, Ho CB, Chiang MCS, Fong YH, Lee PH, So TC, Yeung YK, Leung CY, Cheng YW, Chui SF, Chan AKC, Wong CY, Chan KT, Lee MKY.   +14 more
europepmc   +1 more source

EBSD Study of Creep‐Induced Lattice Misorientation in MgO‐Particle‐Reinforced Austenitic Steel Composites

Advanced Engineering Materials, EarlyView.
Creep experiments at 900°C on coarse‐grained steel‐ceramic composites containing recycled magnesia reveal that higher ceramic volume fractions significantly enhance the creep resistance. Detailed EBSD investigations identify subgrain formation in the steel matrix as the dominant deformation mechanism.
Moritz Müller, Amaya Compart, Mahnaz Mehdizadehlima, Serhii Yaroshevskyi, Christos G. Aneziris, Horst Biermann, Anja Weidner   +6 more
wiley   +1 more source