Results 111 to 120 of about 71,132 (298)

A Robust Adaptive One‐Sample‐Ahead Preview Super‐Twisting Sliding Mode Controller

International Journal of Adaptive Control and Signal Processing, EarlyView.
Block Diagram of the Robust Adaptive One‐Sample‐Ahead Preview Super‐Twisting Sliding Mode Controller. ABSTRACT This article introduces a discrete‐time robust adaptive one‐sample‐ahead preview super‐twisting sliding mode controller. A stability analysis of the controller by Lyapunov criteria is developed to demonstrate its robustness in handling both ...
Guilherme Vieira Hollweg, Paulo Jefferson Dias de Oliveira Evald, Shivam Chaturvedi, Hilton Abilio Gründling, Rodrigo Varella Tambara, Wencong Su   +5 more
wiley   +1 more source

Design of Power System Stabilizer based on Sliding Mode Control Theory for Multi- Machine Power System [PDF]

Journal of Intelligent Procedures in Electrical Technology, 2010
This paper presents a new method for designing of power system stabilizer (PSS) based on sliding mode control (SMC) technique. The control objective is to enhance stability and improve the dynamic response of the multi-machine power system.
Ghazanfar Shahgholian, Amin Rajabi, Bahram Karimi, Mohammad Reza Yousefi   +3 more
doaj  

β‐Catenin/c‐Myc Axis Modulates Autophagy Response to Different Ammonia Concentrations

Advanced Biology, Volume 9, Issue 3, March 2025.
Ammonia, detoxified by the liver into urea and glutamine, impacts autophagy differently at varying levels. Low ammonia activates autophagy via c‐Myc and β‐catenin, while high levels suppress it. Using Huh7 cells and Spf‐ash mice, c‐Myc's role in cytoprotective autophagy is revealed, offering insights into hyperammonemia and potential therapeutic ...
S. Sergio, B. Spedicato, G. Corallo, A. Inguscio, M. Greco, D. Musarò, D. Vergara, A. F. Muro, G. De Sabbata, L. R. Soria, N. Brunetti Pierri, M. Maffia   +11 more
wiley   +1 more source

Revisiting Stability Criteria in Ball‐Milled High‐Entropy Alloys: Do Hume–Rothery and Thermodynamic Rules Equally Apply?

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez, Alejandro F. Manchón‐Gordón, Antonio Vidal‐Crespo, Rafael Caballero‐Flores, Jhon J. Ipus, Clara F. Conde   +5 more
wiley   +1 more source

Power system stabilizer control for wind power to enhance power system stability

, 2011
The paper presents a small signal stability analysis for power systems with wind farm interaction. Power systems have damping oscillation modes that can be excited by disturbance or fault in the grid. The power converters of the wind farms can be used to reduce these oscillations and make the system more stable.
Domínguez García, José Luís, Gomis Bellmunt, Oriol, Bianchi, Fernando Daniel, Sumper, Andreas   +3 more
openaire   +1 more source

DESAIN KONTROLER PID UNTUK MENSTABILKAN TEGANGAN PADA BEBAN BERLEBIH PADA SISTEM TENAGA MULTIMESIN [PDF]

The multi engine power supply system will be stable if there are no interruptions causing increased power consumption, so that the system can be optimized. A survey is carried out to solve this problem.
Ayuningsih, Febrianti
core  

Bistable Mechanisms 3D Printing for Mechanically Programmable Vibration Control

Advanced Engineering Materials, EarlyView.
This work introduces a 3D‐printed bistable mechanism integrated into tuned mass dampers (TMDs) for mechanically adaptive passive vibration suppression. Through optimized geometry, the bistable design provides adaptable vibration reduction across a broad range of scenarios, achieving effective vibration mitigation without complex controls or external ...
Ali Zolfagharian, Frédéric Demoly, Mohammad Lakhi, Bernard Rolfe, Mahdi Bodaghi   +4 more
wiley   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

Damping Inter -Area Electromechanical Oscillation In Two- Area Electrical Power System Using Power System Stabilizer.

Journal of Engineering and Sustainable Development, 2014
In this paper a Delta- Omega Power system stabilizer (PSS) is used to damp the inter – area electromechanical oscillation, the simulated system consists of two fully symmetrical areas linked together by two 230 KV tie lines of 300 Km length. Each area
Adel Ridha Othman
doaj  

Helicopter anti-torque system using fuselage strakes [PDF]

, 1987
The improvement of the helicopter torque control system is discussed. At low to medium forward speeds helicopter performance is limited by the effectiveness of the means for counteracting main rotor torque and controlling sideslip airloads.
Kelley, Henry L., Wilson, John C.
core   +1 more source