Results 71 to 80 of about 1,489,241 (294)

Elinvar Materials: Recent Progress and Challenges

Advanced Engineering Materials, EarlyView.
Elinvar materials, exhibiting temperature‐invariant elastic modulus, are critical for precision instruments and emerging technologies. This article reviews recent progress in the field, with a focus on the anomalous thermoelastic behavior observed in key material systems.
Wenjie Li, Yang Ren
wiley   +1 more source

Application of the Feedback Linearization in Maximum Power Point Tracking Control for Hydraulic Wind Turbine

Energies, 2020
Taking the hydraulic wind turbine as the research object, the method is studied to improve the utilization ratio of wind energy for hydraulic wind turbine, when the wind speed is lower than the rated wind speed.
Chao Ai, Wei Gao, Qinyu Hu, Yankang Zhang, Lijuan Chen, Jiawei Guo, Zengrui Han   +6 more
doaj   +1 more source

Packaging of Macroscopic Material Payloads: Needs, Challenges, Concepts, and Future Directions

Advanced Engineering Materials, EarlyView.
This review introduces a unified framework that decomposes any macroscopic packaging system into the payload, packaging material, and packaging strategy and combines them into a conceptual packaging equation: packaging strategy = payload + packaging material.
Venkata S. R. Jampani, Manos Anyfantakis
wiley   +1 more source

Autocorrelation Based Transmission Power Control in WBANs

2018 12th International Symposium on Medical Information and Communication Technology (ISMICT), 2018
In this paper, we propose an autocorrelation-based transmission power control (A-TPC) method to increase the transmission reliability and reduce the energy consumption. In A-TPC, data packets from multiple sensor nodes are scheduled in the TDMA-fashion.
Hongyun Zhang, Farzad Safaei, Le ChungTran   +2 more
openaire   +2 more sources

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

ACTOR: Adaptive Control of Transmission Power in RPL

Sensors
RPL—Routing Protocol for Low-Power and Lossy Networks (usually pronounced “ripple”)—is the de facto standard for IoT networks. However, it neglects to exploit IoT devices’ full capacity to optimize their transmission power, mainly because it is quite challenging to do so in parallel with the routing strategy, given the dynamic nature of wireless links ...
Iliar Rabet, Hossein Fotouhi, Mário Alves, Maryam Vahabi, Mats Björkman   +4 more
openaire   +3 more sources

EBSD Study of Creep‐Induced Lattice Misorientation in MgO‐Particle‐Reinforced Austenitic Steel Composites

Advanced Engineering Materials, EarlyView.
Creep experiments at 900°C on coarse‐grained steel‐ceramic composites containing recycled magnesia reveal that higher ceramic volume fractions significantly enhance the creep resistance. Detailed EBSD investigations identify subgrain formation in the steel matrix as the dominant deformation mechanism.
Moritz Müller, Amaya Compart, Mahnaz Mehdizadehlima, Serhii Yaroshevskyi, Christos G. Aneziris, Horst Biermann, Anja Weidner   +6 more
wiley   +1 more source

Bi‐level optimization of multi‐regional power system considering low‐carbon oriented synergy of both source and load sides

IET Renewable Power Generation
The expansion of low‐carbon power generation has led to increased complexity in the dispatching mode of the power system. To achieve low‐carbon economic operation for multi‐regional power systems, this study proposes a decentralized dispatch architecture
Wang Liao, Dong Liu, Yufeng Wu, Tianyuan Liu   +3 more
doaj   +1 more source

Influence of an Argon/Silane Atmosphere on the Temperature of a Thermal Plasma

Advanced Engineering Materials, EarlyView.
The influence of a silane‐doped argon atmosphere on the chemical composition and temperature of a thermal nontransferring argon plasma is investigated using optical emission spectroscopy. As a result of the high amount of free electrons resulting from the stepwise ionization and dissociation of the silane molecule, even a silane addition of 0.01 vol ...
Lena Kreie, David Kramer, Thomas Scheithauer, Hans Jürgen Maier, Thomas Hassel   +4 more
wiley   +1 more source