Results 101 to 110 of about 188,995 (261)

Investigating hydrological modeling uncertainties in the Mediterranean region by combining precipitation and soil moisture products

Journal of Hydrology: Regional Studies
Study region: The study focus on five catchments in the Mediterranean Region distributed over Spain, France, Italy, Tunisia and Algeria. Study focus: The study runs four lumped parameter hydrological models combining eight precipitation products and four
Vianney Sivelle, Christian Massari, Yves Tramblay, Paolo Filippucci, Hamouda Dakhlaoui, Pere Quintana-Seguí, Roger Clavera-Gispert, Hamouda Boutaghane, Tayeb Boulmaiz, Raphael Quast, Mariette Vreugdenhill   +10 more
doaj   +1 more source

Influence of Geometric Design on Mechanical Performance of Auxetic Metastructure

Advanced Engineering Materials, EarlyView.
Strategic geometric reinforcement transforms auxetic performance. This study evaluates 3D‐printed arrowhead metastructures, revealing that a modified design with local ring reinforcement suppresses premature failure to achieve superior energy absorption and structural efficiency.
Muhammad Gulzari, Supharoek Sornsomrit, Muhammad Ayaz Akbar, Stephan Rudykh   +3 more
wiley   +1 more source

The role of extreme precipitation in driving the humidification of northwest China from 1961 to 2020

Weather and Climate Extremes
Northwest China is a typical arid and semi-arid region, and a critical climate-sensitive and vulnerable area. Over the past few decades, the region has experienced a significant humidification trend.
Lijuan Hua, Linhao Zhong, Zhaohui Gong, Zhuguo Ma   +3 more
doaj   +1 more source

A Dislocation Perspective on Strength and Toughness in Ceramics

Advanced Engineering Materials, EarlyView.
Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition

Advanced Engineering Materials, EarlyView.
AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

DNA‐Templated 2D Heterostructures as Phototriggered Dynamic Nanohybrids: From Releasing Molecular Loads to Controlling Enzyme Biocatalytic Function

Advanced Functional Materials, EarlyView.
DNA strands are employed both as dynamic linkers and nanoscale templates for the integration of Ag2S nanoparticles on MoS2, which in turn imparted photothermal responsiveness; this feature permits the selective cargo (fluorophore, quantum dots or an enzyme) release from the MoS2 surface in response to local heat induced by light irradiation.
Kai Chen, Haosen Miao, Weiying Hong, Matteo Palma   +3 more
wiley   +1 more source

Liquid Phase Transmission Electron Microscopy: A Window into the Early Stages of Complex Material Formation

Advanced Functional Materials, EarlyView.
Liquid‐phase transmission electron microscopy enables direct observation of nucleation and growth processes in solution. This review is dedicated to the remembrance of Helmut Cölfen and highlights recent studies on complex materials—oxides, biominerals, organic–inorganic crystals—which were central to his research activity. It summarizes key milestones,
Charles Sidhoum, Vinavadini Ramnarain, Nathaly Ortiz Peña, Dris Ihiawakrim, Clément Sanchez, Ovidiu Ersen   +5 more
wiley   +1 more source

Strain‐Programmable Luminescent Adhesive Patch With Tartrazine‐Mediated Optical Skin Clearing for Photochemical Tissue Bonding

Advanced Functional Materials, EarlyView.
We propose a suture‐complementary approach that integrates optical skin clearing with a strain‐programmable luminescent adhesive patch. Hyaluronic acid promotes transdermal delivery of tartrazine to improve optical clearing and stabilizes its interaction with a photosensitizer. Optical clearing increases the penetration depth of visible light into skin,
Seong‐Jong Kim, Kyungjoo Jo, Kwanghyeon Park, Jun Hee Kim, Jong Hyeong Cho, Inhoo Choi, Sei Kwang Hahn   +6 more
wiley   +1 more source