Results 171 to 180 of about 7,716 (287)

Marginal gap of printed, milled, and heat‐pressed two‐piece polyetheretherketone abutments before and after thermal cycling, and their pull‐off bond strength after thermal cycling

Journal of Prosthodontics, EarlyView.
Abstract Purpose To evaluate the marginal gap of two‐piece polyetheretherketone (PEEK) abutments fabricated with different methods, before and after thermal cycling, while also focusing on their pull‐off bond strength. Materials and Methods A two‐piece abutment was virtually designed after digitizing a titanium‐base (Ti‐base) abutment.
Almira Ada Diken Türksayar, Burcu Kanpalta, Naime Bilinç Bulucu, Sandra Schulnig, Sebastian Spintzyk, Münir Demirel, Mustafa Borga Donmez   +6 more
wiley   +1 more source

Parametric Material Optimization and Structural Performance of Engineered Timber Thin-Shell Structures: Comparative Analysis of Gridshell, Segmented, and Hybrid Systems. [PDF]

Materials (Basel)
Golański M, Juchimiuk J, Ogrodnik P, Szulej J, Starzyk A.   +4 more
europepmc   +1 more source

Effect of surface treatments on the bond strength between additively manufactured or injection‐molded high‐performance polymers and titanium

Journal of Prosthodontics, EarlyView.
Abstract Purpose To investigate the effect of surface treatment and fabrication techniques of high‐performance polymers on their shear bond strength (SBS) to grade IV titanium. Materials and Methods A total of 120 pre‐milled titanium abutments were sectioned.
Ahmet Serkan Küçükekenci, Doğu Ömür Dede, Oğuz Süleyman Özdemir, Burak Yilmaz   +3 more
wiley   +1 more source

Experimental Study on Fatigue Performance of Steel Used in U75V Rails. [PDF]

Materials (Basel)
Xu D, Liu G, Wang X, Liu H.
europepmc   +1 more source

Pressure analysis during impression‐making procedure with various tray designs using a digital occlusion analyzer: An in vitro study

Journal of Prosthodontics, EarlyView.
Abstract Purpose The purpose of this study was to evaluate the pressures generated under various relief conditions during impression‐making using the digital occlusal analyzer. Materials and Methods A customized device and impression trays were designed to measure pressure during impression‐making.
Minji Sun, Jaeyoung Kim, Seojune Choi, Hong Seok Moon   +3 more
wiley   +1 more source

Analysis of Fiber Content and Orientation in Prefabricated Slab Elements Made of UHPFRC: Non-Destructive, Destructive, and CT Scanning Methods. [PDF]

Materials (Basel)
Konrád P, Künzel K, Kheml P, Mára M, Carrera K, Beránek L, Hlavůňková L, Fornůsek J, Konvalinka P, Sovják R.   +9 more
europepmc   +1 more source

Fracture load and retention of milled interim implant restorations fabricated on three types of abutments and two implant diameters: An in vitro study

Journal of Prosthodontics, EarlyView.
ABSTRACT Purpose To evaluate the fracture load and retention of subtractively manufactured interim restorations for single‐unit implants of two diameters, using three interim abutment types: stock abutments, titanium base (Ti‐base) abutments, and pre‐milled polymethyl methacrylate (PMMA) abutments.
Dong‐Hun Lee, Carme Riera, Qiucen Wan, Nareudee Limpuangthip, Jae‐Hyun Lee, Sang J. Lee   +5 more
wiley   +1 more source

Importance of Prefabrication to Easing Construction Workers' Experience of Mental Health Stressors. [PDF]

Int J Environ Res Public Health
Fagbenro RK, Sunindijo RY, Illankoon C, Frimpong S.   +3 more
europepmc   +1 more source

Assessment of fit accuracy and retentive strength of additively manufactured zirconia crowns luted to Ti‐base abutments with different resin cements: An in vitro study

Journal of Prosthodontics, EarlyView.
Abstract Purpose This study investigated the influence of cement gap size on the marginal and internal fit, and cement gap size and type on retention of additively manufactured zirconia (AM‐Z) crowns on titanium bases (Ti‐base). Materials and Methods A total of 135 zirconia crowns were designed with three different cement gap sizes: 20 µm, 30 µm, and ...
Rafat Sasany, Sultan Merve Uçar, Burak Yilmaz   +2 more
wiley   +1 more source

Perception of lean construction implementation barriers in the indian prefabrication sector. [PDF]

Heliyon
Negi P, Thakur G, Singh R, Gehlot A, Thakur AK, Gupta LR, Priyadarshi N, Twala B.   +7 more
europepmc   +1 more source