Results 141 to 150 of about 769,233 (317)

Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy

Advanced Engineering Materials, EarlyView.
A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang, Aparajita Pramanik, Sandipan Sen, Shubhashis Dixit, Marcel Muench, R. J. Vikram, Daniel Schliephake, Yolita M. Eggeler, Ankur Chauhan, Martin Heilmaier, Alexander Kauffmann   +10 more
wiley   +1 more source

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

Recycling of NiTi Shape Memory Alloys: Fundamental and Technological Aspects of a Vacuum Induction Melting Processing Route

Advanced Engineering Materials, EarlyView.
The present study investigates recycling of NiTi shape memory alloys via vacuum induction melting. An ingot was synthesized from elemental Ni and Ti and subjected to three subsequent remelting cycles. Remelting increases process durations and impurity levels and adversely affects microstructures and functional properties.
Sakia Sophia Noorzayee, Son Tung Mai, Sarath Menon, Braulio Gadiel Sánchez Ortega, Ralf Drautz, Alexander Kauffmann, Gunther Eggeler, Jan Frenzel   +7 more
wiley   +1 more source

Fibrinogen as a risk factor for premature myocardial infarction in Iranian patients: A case control study

, 2009
Mohammad Shojaie, Morteza Pourahmad, Ahad Eshraghian, Hamid Reza Izadi, Farzan NaghshvarPeymanieh Hospital, Internal Medicine Department, Jahrom University of Medical Sciences, Jahrom, Fars, IranBackground: Premature myocardial infarction with life ...
et al, Mohammad Shojaie, Ahad Eshraghian, Morteza Pourahmad   +3 more
core  

Evaluation of Plasticity and Creep Parameters From Tensile Stress–Strain Data for a Range of Strain Rates

Advanced Engineering Materials, EarlyView.
This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley   +1 more source

The hypothalamic-pituitary-adrenal axis and perinatal treatment of premature foals

, 2013
The danger and vulnerability associated with a preterm birth seem to be closely correlated with a dysfunction of the fetal hypothalamic-pituitary-adrenal (HPA) axis, whose maturation in the foal is without a doubt as delicate as it is important. Not only
Göransson, Lina
core  

Superb Microvascular Imaging for Detecting Ovarian Vascularity in Precocious Puberty, Premature Thelarche, and Pubertal Girls

Objective: We aimed to evaluate ovarian vascularity with superb microvascular imaging (SMI) and to compare it with other conventional Doppler imaging methods in girls with premature thelarche, precocious puberty, and those at puberty. Methods: A total
Ayşe Gül Alımlı, Eda Mengen Uçaktürk, Nazlı Gülsüm Akyel, Mesut Sivri, Havva Akmaz Ünlü, Seyit Ahmet Uçaktürk   +5 more
core   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

Māori whānau experiences of a neonatal intensive care unit: Waikato hospital

, 2009
This thesis topic emerged from my personal experience of having a premature baby in the Neonatal Intensive Care Unit (NICU) at Waikato hospital. My whānau and I felt like aliens; culturally inept, and totally alone during our time in the NICU.
Thompson, Keri
core  

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source